I spoke with Lippert and they said the Kwikee Electric RV Step Complete Assembly, 40 Series, # LC3726892 will be a direct replacement for the Coach Steps 725-0043. It will be a bolt-on install for replacement of the steps. view full answer...
We do indeed have a replacement key 2862 that will work with your Karrite rooftop cargo box, which is the following part:
- Replacement Key for Thule Racks and Carriers # THKEYN2862 view full answer...
We have previously confirmed with Dometic (who own Atwood now) that the Atwood 91349 that you've got can be replaced by the Replacement Control Panel for Atwood Water Heaters # AT91367 you were looking at. view full answer...
From the image you provided, to me, it does not appear that these are replaceable bulbs. Is there a manufacturer marking on the light, part number? Please look at the attached to see if this will be a match for replacing, they are 4-1/2 diameter LED RV interior lights, # 328-K-1051SQ9, or # 328-K-1050Q9.
See the attached product review videos. view full answer...
I was able to find a couple pictures of your 2018 Sportsman 210 BHLE online and from what I saw the correct taillight lens would be the part # AST61B that you referenced. view full answer...
The correct replacement TruXedo TruXport Soft Tonneau Cover # TX281101 on your 2001 Chevrolet Silverado 2500 with a 6-1/2 foot bed is part # TX281101-CVR. Thanks for the P/N number! view full answer...
Yes. The Replacement Antenna for Furrion Vision 1, 2, and S Wireless RV Camera Systems # 772577 will fit on your Furrion FOS48TA-BL. view full answer...
The Dutton-Lainson Hand Winch w/ Automatic Brake - TUFFPLATE Finish - Freewheel - 1,500 lbs # DL14996 will work on that 3.75 wide plate. The mounting holes are 2-1/4 inches on center and about 3-1/2 inches from the back mount hole. The width of the base is the standard 5 inches wide. If you need something smaller, you will need to reduce the winch capacity and use the Dutton-Lainson Hand Winch w/ Automatic Brake - TUFFPLATE Finish - 1,200 lbs - left hand # DL16331 which has the 3-5/8... view full answer...
The RV Landing Gear Switch part # 37213635 is a four prong plug which is common on some RVs . While it is impossible to tell what landing gear is on the trailer other than getting the information off of the gear itself. If your is a four wire plug this will likely replace it. view full answer...
That number doesn't give me a cross-reference. To get a replacement you will need to pull the bearings out of the hub and on the face of both the inner and outer bearing there will be a number printed on the bearing face. If you can give me those numbers I likely can help you out with the correct replacement. I also will need to know the bolt pattern of your hub if you want to keep the same wheels.
If you can't determine the bearing numbers, then you can use a digital caliper like... view full answer...
The Bulldog Cast Head Coupler w/ Wedge Latch part # BDA256C0317 and others like it do not have any adjustment. They are set at the factory and sealed off basically from there. There can be slight variances in them when manufactured or there is the chance that the coupler itself was deformed slightly before you ever received it.
When working with customers this does not seem to be an issue that seems to come up a lot or is persistent. I'm confident that by replacing it you will have less... view full answer...
We don't sell Hyper Tough brand racks, but if the post on your rack is 1-3/8" x 1-3/8" you might be able to make the Replacement Frame Hook for Hollywood Racks Sport Rider or Trail Rider Z-Spec Bike Racks # HRBS-SPRFHLZ (short hook).
I've also linked our entire selection of hooks that you can have a look at to see if there is something that would match if those don't. view full answer...
Yes, you can absolutely get the installation hardware for the Curt trailer hitch # C12083.
What you need is the Replacement Hardware Kit for Trailer Hitches # RHK.
All you need to do is click # RHK, enter "C12083" in the "Hitch Item Number" box, select "Curt" from the drop-down menu, and hit “Add to Cart” to place your order. I have added a link to a video install of this hitch on a 2013 Acura RDX for you as well to take a look at. view full answer...
The 2004 Forest River Wildcat 5th Wheel uses 5,200 lb axles so for brakes you can use the Electric Trailer Brake Kit part # AKEBRK-7-SA. For bearings/seals, you'll need the Bearing Kit part # BK3-310 if you have 2.125" seals or part # BK3-300 if you have 2.250" seals. In order to confirm this you'd need to measure the spindle where the seal rides or you can just get both kit and you'd have extra bearings. view full answer...
The Pull Pin, Easy Swivel Trailer Jack with 6" Wheel - Sidewind - 1,000 lbs. by Dutton-Lainson # DL22560 is similar to, but better than, the Pro Series # PSEJ10000101 jack that you currently have, plus it's made in the USA. This is a solid trailer jack choice and it has received some really great feedback from those who have used it.
I have attached a review video for you to check out as well as a link to our selection of Dutton-Lainson trailer jacks (all made in the USA) in case you wanted... view full answer...
The Lippert 4,400 lb axles use the same bearings and seals as a Lippert 3,500 lb axle so you can use the Bearing Kit for #84 Spindle part # BK2-100 or just the Grease Seal part # RG06-050. view full answer...
For Coleman-Mach Air Conditioners we have the MaxxAir Replacement Shroud # MA00-325001. This particular unit is designed for many of the Coleman-Mach models but I do recommend comparing its dimensions to what you currently have available to ensure a proper fit.
This shroud has overall dimensions of 41-5/8 inches long, 29-3/8 inches wide, and 12-3/4 inches tall. I have attached a couple images that include some additional measurements as well.
If you find that your existing shroud is... view full answer...
I have a solution for you, but the Putco Element In-Channel Window Vent # P480015 is not available in a 4 piece set and are the only available set that comes in a chrome color. I recommend going with the Weather Tech Side Window Air Deflectors # WT84184 , which is a front and rear set that comes with dark tinting that still allows fresh air in while keeping the bad weather out. view full answer...
Since most bike rack manufacturers use proprietary hitch pins, universal fits like this Heininger HitchMate # HE6001 can't be confirmed to work but there is an alternative.
Replacement Hitch Bolt and Clip for Yakima HoldUp # Y8890200 with the Yakima HitchLock # Y07235 will do what you want and is confirmed to fit the Yakima Hold Up Rack # Y02443. I have included video overviews for both of these products for more information. view full answer...
I really wish we had replacement parts still for the Atwood couplers but since they've been out of business for so long we don't have any way to get the parts you are wanting. view full answer...
Go To Results