bing tracking image

Filter Questions and Answers:

reset filter

Expert Answers about Cobra


  • Replacement Roof Vent For Pop Up Trailer
  • The standard for RV/Camper vents is 14 inches by 14 inches. So the Vent Cover for Ventline Old-Style Rounded Dome Trailer Roof Vents - Smoke # BV0554-03 will work. I would suggest the Ventline E-Z Lift Ventadome Trailer Roof Vent - Manual Lift - 14-1/4" x 14-1/4" - Smoke # V3092-603-00. For its easy use and locking handle. With older models it may be harder to find specific parts, if you measure the opening it should be 14-1/4x14-1/4 but they are all rough measurements since its the cut...
    view full answer...

  • How to Wire the Atwood Single-Panel On/Off Switch part # AT91959
  • In order to help you wire the Atwood Single-Panel On/Off Switch part # AT91959, I would need to know the model number of your unit as each will be wired a bit differently. If you can provide me with this exact information then I would be glad to tell you exactly where each wire goes. However, I have attached a few diagrams for you below which list possible ways the switch can be wired depending on the model number. If you don't see your model number below then please let me know.
    view full answer...

  • How To Find Correct Bearings for Cobra Flagstaff Trailer Trailer
  • The easiest way to find the correct bearings for a trailer without pulling the hub is by determining the axle capacity, there's usually a tag on the actual axle with this info. The smaller trailers usually use the Bearing Kit, L44649 Inner/Outer Bearings part # BK1-150 which is common on 2,000-2,200 lb axles. If this is not what you have let me know.
    view full answer...

  • Valterra Waste Valve Seal Kit for Old Style Valves
  • We describe the Valterra Replacement Seals and Hardware Kit # T1003-7VP as being intended for the "old style" 3-inch waste valves. This is also how they are described on the Valterra website. The 9VP kit # T1003-9VP is for use with the Bladex type waste valves like # T1003DSPB. These seals are the same 3-inch size but have a slightly different profile.
    view full answer...

  • RV Power Control Center and Converter for Upgrading From 30 Amp to 50 Amp Service
  • To convert from 30 amp service to 50 amp service the best option is the Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger # PD4560K18LS8. This is designed to give you 50 amp service and will be a fantastic option for you to upgrade. It is 14-1/8" tall x 11-3/16" wide x 8-1/2" deep overall but fits in a 13-1/4" tall x 10-1/8" wide cut out. That means you will need to build in some supports on the side in order to get this to fit properly, but once...
    view full answer...

  • How to Pick Out Replacement Hub and Brake Assembly for 1990 Salem Cobra Travel Trailer
  • In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your wheels. I attached an FAQ article on determining bolt pattern for you to check out. Next thing you will need to know is what spindle you have on your trailer. In order to do that you can either get the inner and outer bearing numbers from a hub...
    view full answer...

  • How to Pick Out Replacement Landing Gear for 1994 Cobra Sandpiper Fifth Wheel
  • I attached a picture that shows where the 17-1/2 inch measurement needs to be taken from for one of our landing gear kits to fit directly. You might double check that you measured from the right place. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Bulldog Tandem Landing Gear Set # BD500162. Either way this landing gear set would work well for you, you just might have to have the brackets of your...
    view full answer...