Expert Answers about Chrysler
- Complete Flat Towing Setup for a 2005 Chrysler Crossfire
- It sounds like the lady you spoke with didn't really know what she was talking about because you absolutely can install a base plate on your Chrysler Crossfire.
The Blue Ox Base Plate Kit # BX1972 is what you'll want to take a look at. This base plate is going to require some minor drilling and trimming of the air dam for installation, however.
You're also going to need a tow bar # e47ZR, a braking system # BLU37TR, and a wiring harness # RM-15267 to complete your flat tow setup.
view full answer... - Trouble With Draw-Tite Trailer Hitch Receiver Hitting Pan For Stow-N-Go Seats on a 2008 Chrysler Tow
- It sounds like your Draw-Tite Max-Frame Trailer Hitch Receiver # 75579 for your 2008 Chrysler Town and Country may have gotten bent in shipping. We have installed this receiver on several different model years with the stow-n-go seats in our shop without an issue. I have linked an article near the bottom of the page which we created to help identify if this is the case on your hitch and what steps are needed to correct it. I personally always find it easiest to measure the mounting holes...
view full answer... - Recommended 7-Way Wiring Harness for a 2013 Chrysler Town and Country
- The Tekonsha OEM Replacement Vehicle Wiring Harness w Brake Controller Adapter item # 22121 will definitely work on your 2013 Town and Country. This is by far the easiest way to add a 7-way connector to your Chrysler. I have linked the installation instructions below.
The Tekonsha Voyager item # 39510 and the Tekonsha Prodigy P3 item # 90195 are two different brake controllers but both will plug into the adapter that is included with the item # 22121 harness. The P3 is a top of the line...
view full answer... - Will the Curt Hitch Pin and Clip Work To Attach a Rear Cargo Trailer Basket
- The # C21410 Curt Hitch Pin and Clip will work for your rear cargo trailer basket as long as you have a 1-1/4" hitch. This hitch pin is designed for 1-1/4" hitches and has a 1/2" diameter with a 2" span. This works for Class I and Class II hitches. If you need one for a 2" hitch you can use the # C21510 instead.
I have attached a review video for your reference.
view full answer... - Fitting A Trailer Hitch Receiver To A 2012 Chrysler 200
- I recommend the Draw-Tite Sport Class I, part # 24871 as a good pick to support the bike rack.
The Draw-Tite Sport doesn't require any trimming or drilling for installation, and I've included a video of our install team putting this hitch onto a 2012 Chrysler 200 so you can get an idea of how the process goes, and our help article with tips on installing a hitch to make the process as easy and quick as possible.
view full answer... - Best Looking Trailer Hitch Receiver For a 2022 Chrysler Pacifica
- The Hidden Hitch by Draw-Tite Trailer Hitch Receiver # DT46GR is the best looking receiver for your 2022 Chrysler Pacifica. This is due to being the only receiver with a removable 2" receiver. When you are not towing or using the receiver for carrying a hitch mounted accessory you can simply remove the receiver by unlocking it from the main assembly. This will allow you to maintain the factory appearance when not in use.
I recommend installing the T-One Vehicle Wiring Harness # TK96FR...
view full answer... - Suspension Enhancement to Fit a 2020 Chrysler Pacifica
- Thanks for reaching out, Eugene!
The only suspension enhancement available for your 2020 Chrysler Pacifica is the Coil SumoSprings Custom Helper Springs # CSS-1168F which are a little different than traditional SumoSprings, but they will still get the job done and provide you with the support you're needing.
Attached is a review video for your reference.
view full answer... - Can etrailer Locking Hitch Pin be Used for Thule Bike Rack
- The etrailer Threaded Anti-Rattle Hitch Pin Lock # e99047 is an M16 bolt while the bolt that comes with the Thule Snug Tite Hitch Lock # THSTL2 is an M12, so even if the thread count was the same they wouldn't be compatible.
If you're just needing to replace the bolt for your Thule bike rack then you can use part # TH62RE, otherwise if you need the lock and washers then you'll need the kit # THSTL2 instead.
view full answer... - Where to Install Block Heater on 2008 Chrysler PT Cruiser
- According to Kat's Heaters the installation location for the # KH11812 is on the backside of the engine, close to the firewall, halfway up the engine block, close to the bell housing – not the timing set.
view full answer... - Roadmaster Base Plate Kit that Fits 2006 Chrysler PT GT
- Hey Michael, we do have a Roadmaster base plate kit that fits your 2006 Chrysler PT Cruiser GT turbo with the part # 278-1. If you are looking for just the removable arms you'd need the part # RM-ARMS instead.
view full answer... - What Trailer Hitch Fits 2023 Chrysler Pacifica Hybrid & 2018 Chrysler Pacifica
- Hello Ed,
While we have hitches that fit both the 2023 Chrysler Pacifica Hybrid as well as 2018 Chrysler Pacifica, I'm unable to directly answer "will that hitch fit" as you didn't say a part number and I couldn't locate a previous order. What I can do though, is list the trio of hitches that fit both the 2018 Chrysler Pacifica and 2023 Chrysler Pacifica Hybrid so you can see if one of these is a match.
- Curt Trailer Hitch Receiver - Class II - 1-1/4" # C12180
- Curt Trailer Hitch Receiver...
view full answer... - Ball Mount Option for 1-1/4 inch Hitch that Needs 2 inch Drop
- Hey Dukane, the closest ball mount we have to what you mentioned wanting is the Curt part # C45018 which can do a drop of 1-1/4 inches. Unfortunately there isn't every single drop dimension available so best option is to go with one that is as close as possible that's maybe a little higher so that once there's some weight on the hitch it will sit level which the option I mentioned would do well.
view full answer... - Can I Use a Weight Distribution Hitch on a 2006 Chrysler Pacifica With Self Leveling Rear Shocks
- You can use any standard Weight Distribution (WD) system with the self leveling shocks on your 2006 Chrysler Pacifica.
Keep in mind that you will need to check your owner's manual before towing with your Pacifica so that you know the Gross Towing Weight for your vehicle.
When choosing a WD system, you will want to find one that has a weight range that you Total Tongue Weight (TTW) falls in the middle of. Total Tongue Weight is the Tongue Weight of your loaded and ready-to-go trailer,...
view full answer...
Go To Results