Customers compare BWHB94009 to these similar products
Products Featured in this Video
Today we're going to review part number BWHB94009. This is the B & W 2 5/16" hitch ball with the long shank and a 30,000 pound weight capacity. Now, this hitch ball will provide connection point to the trailer's coupler. It is designed for very heavy-duty towing. It is a heat-treated steel which is very durable. It has a very raw finish to it.… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
Yes, we also have the Replacement Right Arm #Y76KV for the Yakima EXO SwingBase #Y34VR. This is the other side from the Left Arm #Y66KV you found.
view full answer...I got some information from Yakima and included a diagram of the EXO SwingBase #Y34VR, which is the base part for the EXO SwingBase 2 Tier #Y82VR. Though the measurement from the pin hole to the closest edge of the carrier is not included in said…
view full answer...The B&W 2-5/16" Hitch Ball - 1-1/4" Diameter x 2-1/2" Long Shank #BWHB94004 has a nut that is the traditional socket size of 1-7/8 inch and has fine threads that are 12 threads per inch to fit that 1-1/4 diameter…
view full answer...I have to go off the GM dealership recommendation. If they are saying you need the Hydrastar #HBA-CAM or Dexter #DX35FR adapter module for your factory brake controller to work with your electric over hydraulic brake actuator, then I can't…
view full answer...Since your Ford F-250 is a 6-3/4-foot short bed and your Grand Design Reflection 29RS 5th wheel does not have a tapered nose for increased turning clearance you will need a slider hitch to be able to safely make tight turns, or you can install a…
view full answer...From your measurements and the nose of your trailer it sounds like you will be able to use the B&W Companion #BWRVK3500-5W with your 2013 Ford F-350 Short Bed. However, you're cutting it close, and may run into issues on uneven ground…
view full answer...You will want the hitch to be set at the height that 1) allows the trailer to be level, and 2) allows you a minimum of 6 inches between the bottom of the trailer loft and the top of the bed rails. The fifth wheel hitches offer several inches of up…
view full answer...If you have a Lippert 7k axle the Dexter Nev R Adjust Assemblies part #23-464-465 will fit and work well. Dexter and Lippert brake assemblies are made to the same dimensions and bolt pattern so they can be interchanged.
view full answer...The black wire of the Hayes controller part #HA100400C is for the 12 volt power source. This powers the controller. The red wire will need to attach to the output side of the truck or tractor's stoplight switch. White is ground. The blue…
view full answer...To allow your Dexter DX series electric over hydraulic system # K71-651 work with the integrated brake controllers of your two GM trucks you will need the adapter part #DX35FR and you'd be set.
view full answer...When I reached out to B & W regarding your question, they advised me that the product #BWHB94004 is not rated for use with a gooseneck. That product is made more for a hitch ball opening on a bumper and it is a threaded application. I have linked…
view full answer...If your Ford F-450 has an actual bed and is not a cab and chassis model (with a service bed or flatbed) then you can use the Curt universal folding gooseneck ball rail kit #C61502. You could then use Curt hitch #C-52 or #C65500. A custom hitch for a…
view full answer...