Replacement Door for Suburban RV Water Heater # 6261APW

Question

Question:

I looked and looked at your website but cant find the repalcement Suburban water heater door, frame, and screws, p/n 6261APW. Do you have one? cost?

asked by: Namae K

0

Expert Reply:

We do carry a few replacement parts for Suburban RV water heaters, such as the Camco RV Insect Screen for Suburban 10-Gallon Water Heater Vent # CAM42146. We also offer a similar screen for their smaller 6-gallon units, part # CAM42151. However, we do not have the replacement door # 6261APW that you referenced.

expert reply by: Adam R

0

Answer 1

I am happy to explain the different in cut out sizes for the Furrion RV Electric Fireplace with Crystals - 30" Wide - Recessed Mount - Black part #FF30SC15ABL Julie. The Furrion RV Electric Fireplace with Crystals is designed to go into a…

view full answer...

Answer 2

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 3

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 4

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 5

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

We have a really great kit that comes with everything you'd need to convert your 2021 Vanleigh Pinecrest 335RLP from tandem 6k drum brakes to electric over hydraulic disc brakes with the HydraStar Disc Brake Kit w/ Actuator for Triple Axle…

view full answer...

Answer 8

I have added a photo detailing the wiring connections for the Pollack Heavy-Duty, 7-Pole, Round Pin conncetor, #PK11700, see link. This is a SAE J560 compliant connector. The wiring diagram for the vehicle side connector, #PK11720, is pictured also.…

view full answer...

Answer 9

We do offer the Trailer Connector Adapter, #HM47425, which converts a 7-pole round connector to a 7-pole flat connector. This adapter works for tow vehicles with combined taillight wiring, meaning that the turn signals and brake lights run on the…

view full answer...

Answer 10

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 11

I looked up pictures of the taillights that are on the 3110 Featherlite trailers and for the LED version of them you would want the part #STL36RB and #STL37RB. It looks like the spare tire mounts for your trailer are something you would have to get…

view full answer...

Answer 12

It sounds like you have a wishbone wiring harness install on your trailer. A regular 4-way wiring harness has 4 wires from the back of the connector, 1 for left turn/brake typically (yellow), 1 for the right turn/brake typically (green), 1 for the…

view full answer...

Replacement Door for Suburban RV Water Heater # 6261APW

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching