Will a P3 Brake Controller Plug Into the Same Wiring Harness as a Draw Tite Activator II

Question

Question:

If I replace a DrawTite Activator IV with a Tekonsha Prodigy P3 will the wiring harness need to be changed also?

asked by: Lyle M

1

Helpful Expert Reply:

No, the wiring for a Draw Tite Activator 4 # 5504 and a Prodigy P3 Brake Controller # 90195 are the exact same. It would be just a matter of unplugging the Activator and plugging the P3 in it's place.

expert reply by: Jameson C

1

Answer 1

The ER code on a Reese brake controller typically indicates an internal problem that can't be fixed and requires replacing the controller. Since yours is still working normal I'd say that you are probably on borrowed time with it and will…

view full answer...

Answer 2

I wish I had better news, but the ER code means that there is an internal problem on the Draw Tite Activator part #5504 and that it needs to be replaced. For a new brake controller I would recommend the Prodigy P2 Brake Controller part #90885. This…

view full answer...

Answer 3

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

Answer 7

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 8

To install the Tekonsha Prodigy P3 Trailer Brake Controller #90195 in your Freightliner S2RV chassis the wiring is behind the kick panel in the drivers compartment. There is not a connector on the wires, they are simply terminated with tape. You will…

view full answer...

Answer 9

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 10

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...

Answer 11

Yes, the lid is available as a replacement part. Based on the part numbers you gave me the correct replacement lid is the #FVK1020-19. For the lift arm you can use the #FVK8011-05.

view full answer...

Will a P3 Brake Controller Plug Into the Same Wiring Harness as a Draw Tite Activator II

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching