Where Does a Brake Controller Plug In on a 2008 Ford F-250 XLT

Question

Question:

cannot find the plugin for the break control under the dash any hints where to look it is a 2008 f250 xl the extra 4 up lift switches are installed thanks for the help

asked by: Paul

0

Expert Reply:

On your 2008 Ford F-250 there is a panel you will need to remove on the middle console, passenger side. If you remove that you will have access to where the brake controller needs to plug in. I have included a picture that should help.

expert reply by: Michael H

0

click to enlarge

Answer 1

Great questions! The Curt Echo Wireless Trailer Brake Controller #C51180 will operate using the settings that you chose in the iPhone app regardless of whether you have the app pulled up or not so you can jump from one app to the next or even turn…

view full answer...

Answer 2

That's correct, any emergency like what you're describing would warrant the use of the manual override braking. The manual override function on the Curt Echo Under-Dash Trailer Brake Controller - Bluetooth #C27JR will be activated…

view full answer...

Answer 3

As the Manual Override Button for Curt Echo Brake Controller #C83HR is just the manual override, it will engage the brakes fully when pressed. If you have the controller set pretty low, you could use it to feather the brakes a bit, but you will need…

view full answer...

Answer 4

When it comes to The Curt Echo Brake Controller #C51180 if the Bluetooth gets disconnected or if you lose service, or if your phone battery dies, the last setting you had for the controller would be retained, but you will lose the ability to use the…

view full answer...

Answer 5

The Redarc Tow-Pro Liberty #RED24FR would be a great choice for your 2022 Jeep Cherokee Trailhawk. There are other options but this brake controller is my personal favorite. It is reliable and stays out of your way with only the knob showing in the…

view full answer...

Answer 6

For your 2021 Jeep Wrangler 4xe I recommend the Tekonsha Prodigy P3 Trailer Brake Controller #90195. This brake controller will give you proportional braking which automatically adjust braking force to your Flagstaff based on how hard or light the…

view full answer...

Answer 7

Since you have the tow package, you'll have an easy install. You'll need the #3014-P brake controller harness that would plug into the factory tow package connector located behind and to the right of the OBDII connector, as shown in the…

view full answer...

Answer 8

In order to install the Curt Discovery Trailer Brake Controller part #C84VV on a 2020 Jeep Grand Cherokee you will need the Curt Custom Wiring Adapter for Trailer Brake Controllers part #C51446 which makes for a plug and play installation.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Where Does a Brake Controller Plug In on a 2008 Ford F-250 XLT

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching