Can You Back Up Using a Weight Distribution System with Dual Cam Sway Control

Question

Question:

Do you have to remove/disengage the dual cam sway control before backing up like I did with my old friction control system? Or can you back up with it in place without worrying about bending/breaking things?

asked by: Jim C

0

Expert Reply:

There is no problem backing up with a Dual-Cam sway control system. They work very differently than the old friction bars and will not bind like the friction bars.

expert reply by: Patrick B

0

Answer 1

The biggest difference between an Equal-I-Zer friction style sway control and a system like a Reese Dual Cam High-Performance Sway Control #RP26002 is that the friction style is passive and the dual cam is active. What is meant by that is that the…

view full answer...

Answer 2

The Firman 3,300-Watt Portable RV Dual Fuel Inverter Generator, #FIR54FR is a dual fuel inverter generator operating on either gas or propane and it does include the propane hose with regulator.

view full answer...

Answer 3

Using several drops of oil, lubricate the springs bars where they contact the weight distribution head. This should be done each day of towing. Wipe down excess oil or dirt and debris. There should be a section on lubrication in your instructions.…

view full answer...

Answer 4

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Can You Back Up Using a Weight Distribution System with Dual Cam Sway Control

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching