Parts Needed to Install a Brake Controller in a 2013 Dodge Durango
Question:
I currently have a hitch being shipped from etrailer. I have held off on the contoller and connections for the moment due to the fact that the local dodge dealer told the person I am having install it, that after it is installed it wont work unless its turned on by the dealer. They are saying that a electronic brake and connections wont work straight out of the box. Does this mean that I am at the mercy of the dealer, which is something I didnt want.
asked by: Phil J
Expert Reply:
I am not sure what your dealer was thinking, but if you have a factory 7-way at the rear of your 2013 Dodge Durango all you would need to install a brake controller in your vehicle would be the proper harness.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. For an install harness you would just need the Brake Controller harness part # TK93VR.
This adapter plugs into the 4-pin connector on your vehicle's built-in brake control wiring harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.
If you do not have a factory 7-way you will need to start with a 4-way (if you do not have one). For that you would want the Curt Wiring Harness part # 118552.
From there you would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Tekonsha
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Article: Brake Controller Installation: Starting from Scratch
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Q&A: How To Add a Fuel Tank To a Truck with 5th Wheel Hitch In Bed
- Q&A: Recommended 16' Mesh Tarp for Dump Trailer
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Article: Best Camper Jacks
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Wiring Diagram for Bargman 7-Way RV Style Connector # WG54006-043
- Q&A: Replacement Trailer Jack Recommendation for Dutton-Lainson Jack on Ranger Trailer
- Q&A: Troubleshooting Kodiak 225 Trailer Brake System that Keeps Breaking Calipers In Half
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)