How to Figure Out How Low the Curt Hitch part # C15810 Would Sit Below Bumper
Question:
How much below the stock bumper does this hang down? The photos of this installed on the Superduty do not have the bumper installed....... Is the receiver as tight to bumper as possible? I want clearance when I am wheeling and not towing. The side plates of the Reese hang down WAY too far, I can clearly see that from your photos. thank you very much,
asked by: David
Expert Reply:
While I don't know exactly how far the Curt Hitch part # C15810 would hang below the bumper of your 2002 Ford Superduty I can tell you how you can figure it out. I went out into our warehouse and measured the distance from the mounting surface of the hitch down to the hitch opening and found that it measures 5-1/2 inches. So basically if you measure 5-1/2 inches down below the rear frame of your truck that is where your hitch opening will be.
![Jameson C](https://images.etrailer.com/static/images/catg/people/371_tn.jpg)
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class V - 2-1/2"
- Trailer Hitch
- Custom Fit Hitch
- Class V
- 2700 lbs TW
- 20000 lbs GTW
- 20000 lbs WD GTW
- 2-1/2 Inch Hitch
- 2700 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Camper Tie-Downs
- Shop: Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb E-Z Lube Axles - 12" - 8 on 6-1/2
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V - 2-1/2"
- Video: Optronics Trailer Lights - Tail Lights - STL101RKB Review
- Shop: Easy Grease Trailer Hub and Drum for 5.2K to 7K Axles - 12" - 8 on 6-1/2 - Galvanized
- Shop: Hitch Box Extension and Reducer for Titan 2-1/2" Trailer Hitches, 24" - 34" Long
- Shop: Curt Ball Mount for 2-1/2" Hitches - 6-1/2" Rise, 8" Drop - 20K
- Shop: 2-5/16" Hitch Ball - 2" Diameter x 3-1/2" Long Shank - Machined - 30,000 lbs
- Shop: HappiJac Camper Tie-Downs - Custom Bed and Bumper Mount - Front and Rear
- Video: Dexter Trailer Hub and Drum Assembly Installation 23-458
- Q&A: How To Mount 7-Way Connector To Curt Trailer Hitch Receiver C15810
- Q&A: Replacement Hitch Mounting Hardware For a Curt 15810 Trailer Hitch
- Q&A: Recommended Class V Trailer Hitch with 2-1/2 Inch Receiver for 2005 Ford F-350 Super Duty
- Video: Review of CURT Trailer Wiring - Easy Mount Electrical Bracket - C58003
- Search Results: 15810
- Shop: Trailer Wiring
- Q&A: Can Trailers Have Shock Absorbers Installed
- Q&A: Drop Measurement of Curt Class V Trailer Hitch # C15810
- Q&A: Dimensions for Curt Trailer Hitch Receiver # C15410 For 2005 Ford F-350 With Utility Bed
- Q&A: Additional Dimensions of Curt Trailer Hitch # C15410