Length of Handle on Ultimate Trailer Jack 322-RDJ-2K

Question

Question:

Do you know what the length of the handle is for the topwind Ultimate Trailer Jack part 322-RDJ-2K? Specifically from the center of the jack to the outermost part of the crank handle. Trying to ensure that this jack will fit given the proximity of the propane tank enclosure on my trailer current jack is a side winder.

asked by: Alan

0

Expert Reply:

Hi Alan,

The length of the handle from center of the jack to the outside is 6-3/4 inches for the Ultimate Trailer Jack # 322-RDJ-2K.

expert reply by: Kyle S

0

Answer 1

It would seem that the 1,750 rating that your tire has is the weight rating, but most ST205/75-14 tires with a Load Range of C have a 1,870 lb capacity at 50 psi like part #AM10229. That would mean that when you combine the two tires you have an…

view full answer...

Answer 2

Sounds like you are looking for a lower profile jack for your trailer so that the tailgate of the vehicle does not interfere with it. I went to our warehouse and was able to locate an a-frame jack that measured less than 12 inches from the bracket…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.

view full answer...

Answer 5

A direct replacement for your Winntec Model 6020 is the Automatic Changeover RV LP Gas Regulator #37207-30395 as the BTU rating is compatible and they have the same fitting sizes.

view full answer...

Answer 6

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 7

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…

view full answer...

Answer 8

I spoke with Lippert and they said the Kwikee 35 Series Electric RV 1-Step part #LC3691461 will be a direct replacement for the Coach Steps 725-0041. It will be a bolt-on install for the most part for the exception of changing out the door switch…

view full answer...

Answer 9

The factory trailer brake controller port on your 2021 Chevrolet Tahoe is located underneath the dash just to the left of the steering wheel. It will be taped to another harness so it may take a bit of looking to find. Keep in mind that if your Tahoe…

view full answer...

Answer 10

If your 2022 Chevrolet Tahoe does not have the factory tow package then the plug may not be there. If this is the case you would need to hardwire in a brake controller. If your Tahoe does have the tow package then the plug will be under the dash. The…

view full answer...

Answer 11

Replacement arms are available for the Roadmaster EZ5 Base Plate Kit #RM-521569-5 for your 2015 Honda Fit with the part #RM-ARMS. When the original base plate brackets and arms were manufactured, they were made as one part. To be sure that the new…

view full answer...

Answer 12

I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The easiest…

view full answer...

Length of Handle on Ultimate Trailer Jack 322-RDJ-2K

Product Page this Question was Asked From

Continue Researching