Availability of Hubs that Fit 2,200 lb Lippert Axle Spindles

Question

Question:

Do you sell a complete hub assembly that will fit this wheel and a Lippert straight spindle axle that has 1-1/16 inch spindles. The axle has a 2,200 lb capacity and a seal surface diameter of 1.5.

asked by: Tommy

0

Expert Reply:

Hey Tommy, yeah we have quite a few hubs that fit the Lippert 2,200 lb axle spindles like the part # 8-258-50UC1 which is an idler hub with a 5 on 4-1/2 inch bolt pattern.

I also attached a link to a page that has all of the 2,200 lb hubs we offer as well.

expert reply by: Jameson C

0

Answer 1

The best option we have for you is the 3-Leaf Double-Eye Spring part #e84SR with the Single-Axle Trailer Hanger Kit part #APS4. This option will replace the leaf springs and leaf spring hanger brackets which is needed because the new double eye leaf…

view full answer...

Answer 2

I have another option for you, but we do not have a 10" diameter wheel that has the 5 on 4-1/2" bolt pattern and a pilot hole of 3.19". The two 10" wheels that we offer with the 5 on 4-1/2" bolt pattern both have a 2.80"…

view full answer...

Answer 3

The pilot diameter on a wheel, like the one with part #AM30620, is the diameter of the bigger hole that is directly in the middle of the wheel. The pilot hole diameter of the wheel for the part I just measured is 2.84". I have attached a picture…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Availability of Hubs that Fit 2,200 lb Lippert Axle Spindles

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching