end links

Question

Question:

Hello i will be ordering a front sway bar RM-1109-149 for my 2014 e450 ford Thor motorhome 31L. Will the end links RO57FR work with this sway bar? Thanks Dave

asked by: David S

1

Helpful Expert Reply:

No they would not as they were designed for a different sway bar.

expert reply by: Jameson C

1

Answer 1

Hey David, for your 2014 Thor 31L Class C motorhome you would want the Roadmaster Front Sway Bar part #RM-1109-149 which is a confirmed fit. This is designed to use factory endlinks though so you'd need to reuse what you have or get new ones…

view full answer...

Answer 2

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 3

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 4

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 5

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 6

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…

view full answer...

Answer 7

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 8

While trailer axles do feature an upward bend like you are describing, there isn't a particular amount/measurement that is standard across the board. This bend in the axle is designed so that it will straighten under a trailer's loaded…

view full answer...

Answer 9

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 10

Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set #AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with a…

view full answer...

Answer 11

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...

Answer 12

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

end links

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching