Lunette Ring Clearance For The Blue Ox Adjustable Ball Mount W/ Pintle Hook # BLU25XR

Question

Question:

What is the spacing between the hitch ball and the vertical part on the back of the hitch? We have an old trailer with an oversized Lunette ring and I want to know if it will fit in the gap I have added a picture for clarification - Im looking at the distance between the two red lines.

asked by: Cameron J

0

Lunette Ring Clearance
(click to enlarge)

Expert Reply:

Hey Cameron,

I was finally able to get my hands on the Blue Ox Adjustable Ball Mount with Pintle Hook for 2-1/2" Hitch # BLU25XR and found the spacing to be 1-7/8".

expert reply by: Kevin C

0

Answer 1

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 2

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 3

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 4

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 7

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 11

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Lunette Ring Clearance For The Blue Ox Adjustable Ball Mount W/ Pintle Hook # BLU25XR

Product Page this Question was Asked From

Continue Researching