B&W 5th Wheel Hitch to Fit Reese Under-Bed Rail for a GM Pickup

Question

Question:

Which BandW hitch fit this Resse RP30868 mount?

asked by: Scott A

0

Expert Reply:

Thanks for reaching out, Scott!

The Under-Bed Rail and Installation Kit for Reese Elite Series 5th Wheel Trailer Hitches # RP30868 uses the same footprint as the Ford OEM puck system so you can use the 25K B&W Companion # BWRVK3305.

expert reply by: Jon G

0

Answer 1

I do have a Reese under-bed fifth wheel install kit that will fit your 1999 Ford F-350, however, the Reese under-bed kit #RP30126 is only designed to fit 2011 - 2013 F-250s and F-350s. The correct Reese under-bed fifth wheel installation kit to fit…

view full answer...

Answer 2

Yes, the Elite Rail Kit adapter part #RP30845 does fit the Reese Elite rail kit part #RP30073 that you referenced. This adapter has a 25k capacity as well. The underbed rail kit part #RP30073 is the correct rail kit for your 2006 Ford F-350 as well…

view full answer...

Answer 3

To use your Signature Series fifth wheel hitch with the Elite Series under-bed rails, you will need the Signature Series Hitch Adapter, #RP58419. If your Signature Series hitch uses a slider, then you will not need to use the handles in this kit, you…

view full answer...

Answer 4

Your Reese Signature Series Fifth Wheel hitch will fit the Elite rail kit part #RP30074, but you will need to use the adapter part #RP58419. The #RP30074 has been confirmed as a fit for your 2008 Dodge Ram 2500 short bed as well.

view full answer...

Answer 5

I spoke with my contact at Reese and he said that you would need to get the whole kit, #58238, if you need to replace any of the anchors on the hitch. The single ones are no longer being provided by themselves.

view full answer...

Answer 6

The Signature Series of 5th wheel trailer hitches from Reese should already have the appropriate feet to install in an aftermarket Reese Elite series installation kit with the 4 pucks or the factory system. If it doesn't then you would need…

view full answer...

Answer 7

Since you purchased a Reese 18K hitch for Ford Factory pucks the foot #58238 is what you need for the older style Signature series fifth wheel hitches and is a replacement foot assembly kit. If you have the newer style, then #RP58419 is what you need…

view full answer...

Answer 8

Your Ford 5th wheel hitch is basically the Reese M5 Series 5th Wheel Trailer Hitch - Single Jaw - 27,000 lbs #RP30922 with Ford branding. I've attached the installation instructions to assist. The Reese Signature Series Hitch Adapter for Elite…

view full answer...

Answer 9

The Reese hitch 30072 is a Signature Series hitch that fits underbed rail systems. So for your 1999 Ford F-350 you'd want the Elite rail kit part #RP30073 which is a confirmed fit. You will also need this adapter part #RP58419 since the hitch you…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

B&W 5th Wheel Hitch to Fit Reese Under-Bed Rail for a GM Pickup

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching