Can I Use a Turning Point Wedge w/ a B&W Companion Hitch and a Reese Sidewinder?

Question

Question:

Will this hitch BWRVK3710 accommodate a Reese Sidewider pinbox with wedge to use a turninginch pinbox?

asked by: Paul M

0

Expert Reply:

Yes, it will. The B&W Companion OEM 5th Wheel Hitch item # BWRVK3710 will work with the Replacement Wedge Block for Lippert Turning Point Pin Box item # LC79UD on a Reese Sidewinder. However, if you don't already have the Turning Point Wedge it's best to use the 5th Airborne Custom Wedge for B&W Fifth Wheels item # SWW-06.

expert reply by: Jerred H

0

Answer 1

Yes, I do and have listed them below: The Replacement Base for B&W Companion item #BWRVB3710 weighs 83 lbs. The Replacement Head Assembly for B&W Companion item #BWRVC3006 weighs 70 lbs. The B&W Companion OEM 5th Wheel Hitch…

view full answer...

Answer 2

The B and W Companion hitch part #BWRVK3710 that you referenced weighs 152 lbs.

view full answer...

Answer 3

For your 2023 GMC Sierra 2500 with an 6-3/4 foot bed, I recommend the B&W Companion OEM item #BWRVK3775. This hitch installs inside your factory puck system and allows you to have full access to your bed when you are not towing. The…

view full answer...

Answer 4

I recommend using the 5th Airborne Custom Wedge for Husky / Valley Fifth Wheels #SWW-04 for your application as we've found it to fit really well with the Turning Point pin boxes. Attached is a review video as well as a clip of a customer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Can I Use a Turning Point Wedge w/ a B&W Companion Hitch and a Reese Sidewinder?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching