How Much Space Should I Have Between the SumoSprings and Axle on a 2012-2023 Jeep Wrangler?

Question

Question:

how much of a gap should there be between sump springs and axle housing on Jeep wrangler?

asked by: Robert C

0

Expert Reply:

The SumoSprings Solo Custom Helper Springs item # SSR-405-47 that fit a 2012 - 2023 Jeep Wrangler should have a 1/2" to an 1" of space between them and your axle.

expert reply by: Jerred H

0

Answer 1

The SumoSprings Solo Custom Helper Springs #SSR-405-47 are a great choice for your 2015 Jeep Wrangler Unlimited if it has a 2 inch lift. I spoke with my contact at SuperSprings and he confirmed that this spring in this system measures 4-1/2 inches.…

view full answer...

Answer 2

There is a generation change between a 2003 Wrangler (TJ), and a 2007 (JK) so the soft top of one would not fit the other. For a TrekTop NX for the 2007 you'd need the part #B5685235.

view full answer...

Answer 3

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 11

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

How Much Space Should I Have Between the SumoSprings and Axle on a 2012-2023 Jeep Wrangler?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching