Correct Replacement Brake Shoes for a Demco Hydraulic Braking Kit

Question

Question:

Hello, I just bought item 40716-15, a DEMCO hydraulic brake package from etrailer. Is this item replacement shoes for the kit ? Thanks

asked by: Mike T

0

Expert Reply:

Yes, the Replacement Brake Shoe Lining for Demco/Dico 10" Free-Backing Hydraulic Brakes # BP04-126 is the correct replacement brake shoes for your Demco Hydraulic Brake Kit # 40716-15.

expert reply by: Bryce D

0

Answer 1

Yes, you can use your DA70 actuator for drum brakes with disc brakes, you just need to switch the master cylinder to the Replacement Master Cylinder for Demco Actuators - Disc Brakes #5672.

view full answer...

Answer 2

If you replace the current brakes on your trailer with the same uni-servo drum brakes and no lockout actuator (like #T2351000), the brakes will deliver 20 percent braking when traveling in reverse. However, the more pressure you apply going backwards…

view full answer...

Answer 3

Knowing the inside diameter of the drum is the key piece of information we need; the brand of the assembly will not be a factor in determining what you will need to replace your hydraulic brakes. You mentioned your trailer's GVW, but it is the…

view full answer...

Answer 4

Good questions. The difference between free backing brakes like the #AKFBBRK-35-D and regular hydraulic drum brakes like #DMSB18794M-93M (referred to as duo or duel servo) is that the wheel brake cylinder has pistons on both sides of the regular/duo…

view full answer...

Answer 5

We do have some parts for the Dico Aero 6000 actuator on your Four Winns boat trailer: Replacement Master Cylinder - #T4395100 (you have to remove the check valve) Replacement Damper - #T4502000 Replacement Lock Spring - #T4501400 Replacement Bolt -…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Correct Replacement Brake Shoes for a Demco Hydraulic Braking Kit

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching