Does Curt 7-Way 56431 Fit 2023 Ford Ranger

Question

Question:

Hi, is this kit going to work for the 2023 Ford Ranger xlt? Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector Item # C56431 I have installed already inside the Ranger this one: CURT 51110 Venturer Electric Trailer Brake Controller, Time-Delay. Wiring inside the car is the same of the 2020/22 Ranger.4 wires Thank you

asked by: Marco

0

Expert Reply:

Yes, the Curt 7-way part # C56431 is a confirmed fit for your 2023 Ford Ranger and will work great with your Curt Venturer # C51110.

expert reply by: Jameson C

0

Answer 1

From all the info I could find, the 2020 Ranger and the 2021 Ranger both use the same stock bumper. With that being said, the 7 Way plug that is included with the Curt #C56431 can definitely be replaced with the 7 Way plug from the #HM40975.

view full answer...

Answer 2

Yes. The Curt #C56431 tees into the existing factory wiring and will leave your factory 4 way connected, so you'll still have the ability to use that for towing as well. I've linked the installation video of this harness for you to…

view full answer...

Answer 3

To add a 7-way connector to your 2023 Ford Ranger you will want the Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector item #C56431. This custom-fit T-connector plugs into your Ranger's wiring harness, which is located…

view full answer...

Answer 4

It is possible to have both a 7-way and 4-way on your 2019 Ford Ranger by using the #C56431 but you will need to replace the 7-way connector with the #C55774 and you'd have one that has both. This uses the same round connector as what comes with…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 11

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Does Curt 7-Way 56431 Fit 2023 Ford Ranger

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching