Can 10" Electric Brakes go on 2,200 lb Axle

Question

Question:

Can I put 10” electric brakes on 2200lb axle with 7” brakes

asked by: Paul

0

Expert Reply:

Ten inch electric brakes cannot go on a 2,200 lb axle because there are no 10" hub and drums for that size axle. I apologize as I know that is not what you wanted to hear but you would need to stick with 7" electric brakes, the Dexter Electric Trailer Brake Kit # 23-47-48.

expert reply by: Kyle S

0

Answer 1

The 4 hole brake mounting flange will work for 10 inch brakes because the 7 inch and 10 inch assemblies use the same 2-7/8 inch on center mounting holes. The brake assemblies like #AKEBRK-35 or self-adjusting assemblies like #AKEBRK-35-SA will both…

view full answer...

Answer 2

There is one hub and drum that will fit the Timbren Axle-Less Trailer Suspension System - Spindle w/Brake Flange - Off-Road Tires - 2,200 lbs #ASR1THDS02. The correct part is the Dexter Trailer Hub and Drum Assembly #84546UC3-EZ. The #DX68XR says it…

view full answer...

Answer 3

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 4

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Can 10" Electric Brakes go on 2,200 lb Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching