Replacement Head for Reese Weight Distribution System

Question

Question:

Will this work with my Reese trunnion bar system and hitch ?

asked by: Lester F

0

Expert Reply:

This actually works with the Pro Series weight distribution systems. The correct replacement head for a Reese system would be the part # RP58167.

expert reply by: Jameson C

0

Answer 1

You have the Pro Series weight distribution head part #58333 which means the correct replacement spring bars you need are the part number #58338 which has a tongue weight range of 600-1,200 which which would work great with a trailer that weighs…

view full answer...

Answer 2

You have a very old system there! You would not be able to add dual-cam sway control #RP26002 to this system. Dual-cam systems require the bars with the cam hook ends and will not work with tapered straight bars. The system would not be a #PS49582…

view full answer...

Answer 3

The correct 1,200 lb tongue weight spring bars for the Pro Series RB2 weight distribution head #58333 you referenced are the part #58338.

view full answer...

Answer 4

You can certainly use the Reese #83660 sway control kit on both sides of your trailer A-frame. There's a couple of ways to do this, but the most simple way would be to use your existing ball mount, and have a #C45822 sway control tab welded on…

view full answer...

Answer 5

My first thought on recommending a replacement for your Fantastic Vent Fan Model 8000, is the MaxxFan Deluxe Roof Vent w/ 12V Fan, #MA00-06401K. This is a 4-speed fan with ceiling fan mode that circulates air when vent is closed. It is a manual…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 10

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 11

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Head for Reese Weight Distribution System

Products Referenced in This Question

Featured Help Information

Instructions

Continue Researching