Can Trailer SumoSprings Kit # TSS-106-40 Fit Distance of 7-3/4 inch From Spring to Trailer Frame

Question

Question:

Hello again, so Im going to reword my question in hopes to get a usable answer . I have a single axle REPLACEMENT, 3.5k, Straight, Spring Axle, Idler, UnderSlung 67mm, 2-5/8 ,axle . I am looking at the sumo spring TSS-106-40 , however I can not get a straight answer on the height of the spring without spacers and the relocation bracket combined, or individually? I have 7.75 or 7 3/4 from the top of leaf spring that is underslung to trailer frame . This measurement is not with trailer jacked up off of tires . This measurement is with the weight in trailer on the springs and tires . Can I make part TSS-106-40 fit this application without the spacers ? Or do I need spacers ? Or even easier . How tall is parts A, B, and C , of the sumo springs TSS-106-40 accumulated or each individualy and I can do the math . The only useful information I can find is the height of the spring itself 4 and the height of spacers .5 . I need the height of the relocation bracket please , the spacers, please, the spring please Individualy . I have now written 5 letters to get this very basic information. I truly hope you can help me . And for the sake of all future Inquiries , it would be great if every single one of you dealers just measured each part and printed it on the advertisement. It could save so much time , recourses, suffering, grief, etc . Thank you for hopefully understanding my question. I look forward to a intelligent, very detailed explanation of each individual parts sizes . Thank you etrailer, you guys rock and I know you will be the ones to answer this very basic information that should be on every advertisement everywhere. Lol Thanks again.

asked by: Ainsley R

0

Expert Reply:

The SumoSprings kit # TSS-106-40 does for sure fit your application based on the dimension you just mentioned of 7-3/4 inches from the spring plate to the bottom of the trailer frame. This kit works with dimensions here that range from 6 to 8-5/8 inches so no further measurements or dimensions would be needed to know this for sure fits.

expert reply by: Jameson C

0

Answer 1

When we installed the SumoSprings Solo Custom Helper Springs #SSR-307-47 on a 2013 Ram 1500 we did not use the included spacer. There are really 2 factors that are going to come into play when deciding if you will need the spacer on your 2016 Ram…

view full answer...

Answer 2

The height of the SumoSprings Trailer Helper Springs w/ Line Relocation Bracket #TSS-106-40 is 4 inches for just the rubber spring portion of it. Since you have 3 inches from the axle to the frame that would indicate that there would be a…

view full answer...

Answer 3

Installing a 4,000 lb capacity leaf spring on a trailer with a 3,500 lb capacity axle will make the suspension stiffer which could then in turn minimize the risk of the axle contacting the frame. However, this is not what I recommend to fix your…

view full answer...

Answer 4

The most likely cause for the incorrect behavior of your trailer lights, where activating one turn signal causes all trailer lights to blink, is an insufficient ground (or a short to ground) on either the vehicle or the trailer. Since you re-wired…

view full answer...

Answer 5

The black wire of the Hopkins 7-Way Molded Trailer Wire Connector #HM20048 carries the 12 volt accessory circuit. This is the circuit that will typically power interior lights or charge a trailer's battery. I attached a help article that…

view full answer...

Answer 6

Once it's disassembled, once you access the rear of the socket you'll see that it's color coded as shown in the provided photo. The corresponding plug, like #A10-30FDT would wire in the same manner. The screws on each terminal…

view full answer...

Answer 7

The Timbren kit part #TTRA1702 is 2-3/4 inches tall and would work great for you to give you additional support. This will provide up to 1,000 lb of additional support.

view full answer...

Answer 8

The Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - Item #JET-5000 that you referenced only has one wire that runs from it, the power wire. This wire would need to get run to the 12 volt accessory circuit of the…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Can Trailer SumoSprings Kit # TSS-106-40 Fit Distance of 7-3/4 inch From Spring to Trailer Frame

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching