Weight Capacity Increase for Yakima LockNLoad Expansion Pack

Question

Question:

This says it adds weight capacity...how much?

asked by: Shawn

0

Expert Reply:

The Yakima LockNLoad platform rack has a 220 lb weight rating when mounted on 2 crossbars. When you add the Expansion Pack # Y24FR it increases to 330 lbs for a 3 crossbar system, or 440 lbs for a 4 crossbar system.

Please note that the weight capacity of your vehicle will likely be less than the capacity for the LockNLoad so you'll need to take that into account as well.

expert reply by: Jon G

0

Answer 1

Yes, you can use your Yakima OverHaul HD Adjustable Truck Bed Ladder Rack #Y01151-58 with the Access TonnoSport Soft, Roll-Up Tonneau Cover #A22040169 on your 2017 Ram 1500 with the 5-1/2' short bed. You will need to install the Yakima…

view full answer...

Answer 2

In order to install the Yakima 72" HD Tracks for Roof Racks, OverHaul HD, and OutPost HD #Y84MR on your vehicle you'd need to use a set of Yakima OutPost HD Overland Truck Bed Rack Uprights #Y01152. If you let me know what vehicle…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 6

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 7

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 8

For your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount #Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need…

view full answer...

Answer 9

I have a Yakima crossbar setup that is compatible with the Retrax Pro XR Tonneau Cover on your 2021 Toyota Tacoma, however, the Yakima Bedrock is not compatible and the 60" crossbars would be too short anyways. I recommend going with the…

view full answer...

Answer 10

You are exactly in the middle between the two sizes of the Yakima Sidebars for the Overhaul HD ladder racks. So what you'd need to do is decide if you'd rather spread the uprights out a little more or push them in closer together to match up…

view full answer...

Answer 11

Hi Ruben; thanks for the question, and while there is one rack for your 2023 Ford F-150 with a 6-1/2' bed compatible with the Pace Edwards UltraGroove Metal Retractable Hard Tonneau Cover #PE66UV, it does not have sides, and is part #TX84NV.…

view full answer...

Weight Capacity Increase for Yakima LockNLoad Expansion Pack

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching