Correct Breaker Size for Replacement 6-Point Controller for Lippert Components Ground Control 2.0

Question

Question:

the front two jacks combined total 60 amps. what size breaker is require for this control assbly?

asked by: Nick

0

Expert Reply:

The Replacement 6-Point Controller for Lippert Components Ground Control 2.0 Electric Leveling System # LC56VR requires a 50 amp circuit breaker. The resettable breaker should be installed between the controller and the battery. This is marked "L" in the diagram below.

expert reply by: Robin H

0

Lippert Ground Control 2.0 6-Point Wiring Diagram.
(click to enlarge)

Answer 1

Yes, the Replacement Control Module for Lippert Ground Control 3.0 Leveling System #LC85ED will work as a replacement, however according to Lippert you need to have the Replacement Control Panel for Lippert Ground Control 3.0 and Travel Trailer RV…

view full answer...

Answer 2

The blank screen on your LCI Ground Control 3.0 could be either a power issue or a control module issue. I recommend first remove the panel and unplug it from the back leaving it unplugged for at least 15 minutes so that it loses all of the residual…

view full answer...

Answer 3

The correct replacement module for the 694654 that you have now is the part #LC85ED.

view full answer...

Answer 4

Sometimes the panels of the LCI leveling kits just get weird bugs in them. Try unplugging the panel at the back and replugging back in and that should take care of the issue. If not let me know and we can reach out to LCI and see what they think is…

view full answer...

Answer 5

I sent all of this to my tech contact at LCI to see what they this is the problem and they were able to come up with a way to use the voltage readings to determine where the issue is: There are 4 wires on the harness as follows Black= power (need to…

view full answer...

Answer 6

Sometimes the displays of the Lippert ground control systems need to be reset. Try unplugging the control panel for several seconds and then plugging it back in. We've seen just doing that alone fix most of the problems with the control panels.

view full answer...

Answer 7

I believe you are looking for the Replacement Low Profile Plunger Bolt for Lippert SolidStep 3.0 Stairs part #LC436574. Check out the video I linked for you on it.

view full answer...

Answer 8

I went ahead and reached out to Lippert, and they confirmed that you need automatic transmission fluid Dexron III or Mercon 5 fluid. This works with their hydraulic auto leveling system. With that being said, I do not recommend using the hydraulic…

view full answer...

Answer 9

I reached out to Lippert who informed me your Power Gear controller 140-1224 Rev 0G is obsolete. It was replaced with the Lippert part number 372854 but that part is also now obsolete. At this point your options are to try and have your controller…

view full answer...

Answer 10

The good news is your system is working. That lets us rule out 2 of the 3 possible components. Before replacing the third one, I recommend unplugging the connections on the panel and cleaning them prior to reconnecting. If this doesn't solve your…

view full answer...

Answer 11

It sounds like the display for the system may just need to be reset; we've seen this reported before and if you can unplug it, let it sit for a few minutes and then plug it back in- it might solve your problem. We've seen just doing that…

view full answer...

Answer 12

Often an issue like you stated has to do with the battery not being fully charged. If the battery is even slightly low, sometimes this system is a little finicky. I recommend first charging your battery fully and testing it to ensure it is fully…

view full answer...

Correct Breaker Size for Replacement 6-Point Controller for Lippert Components Ground Control 2.0

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching