Is the 24 Inch Horse Trailer Breast Pad Pre-Drilled

Question

Question:

Does part # HTP24BK come with holes in it or do you drill your own.

asked by: Tim R

0

Expert Reply:

Horse trailer pad # HTP24BK does not come pre-drilled because then it would limit what and where it could fit. We also recommend trailer horse pad screw # PS-8 to mount the pad. The screws are sold in quantities of 1.

expert reply by: Michael H

0

Answer 1

There is not a specific method for attaching the Horse Trailer Side Pad, #HTP60BK, to the trailer wall. You can use the Trailer Horse Pad Screw, #PS-8, but like you said it will puncture the material. Another option you have is to apply adhesive to…

view full answer...

Answer 2

When replacing your horse trailer pads, be sure to pad all dividers and walls. The pads are constructed of a very durable vinyl sewn over 2" of foam onto rigid cardboard. They stand the test of time and hold up in all climates. There is no need…

view full answer...

Answer 3

We carry Horse Trailer Pad Screws for attaching the horse trailer pads. The part number for the Trailer Horse Pad Screw (Qty 1) is PS-8. The pads are installed in the trailer with the screws directly through the pad and can be secured anywhere it is…

view full answer...

Answer 4

In order to install the the Horse Trailer Side Pad - 60" #HTP1260BK you just need to screw them in. What you'll need are the Trailer Horse Pad Screw #PS-8 and attach them to the sides of the pad.

view full answer...

Answer 5

The holes to attach the Horse Trailer Side Pad part #HTP60BK do need to be drilled but that is standard from the other horse trailer side pads I have researched. We do not carry the screws by the box but the screws that we recommend can be purchased…

view full answer...

Answer 6

You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the foot),…

view full answer...

Answer 7

The caliper bracket you are looking for is the Replacement Mounting Bracket #KCMB12D which is compatible with the 5 bolt mounting flange you have as well as the 225 Kodiak Dacromet calipers you have as well. Then for a bolt kit you'd want the…

view full answer...

Answer 8

You would not be able to charge your battery through the wiring on your 4-way trailer connector. Since your truck has a 7-way connector, you could maintain the power to the battery but not charge it. To begin, you would need to cut off your 4-way…

view full answer...

Answer 9

The 3-1/4 inch diameter hole to install the part #RR5K is the correct dimension to use. We actually even had a customer come back and say they did it with a 3 inch hole saw. I attached a link to the install video you mentioned as well.

view full answer...

Answer 10

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 11

I have spoken with Lippert about the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part #LC675817 in they past and they informed me that the most important aspect is that the battery/batteries are sufficiently charged, between 12.4…

view full answer...

Answer 12

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Is the 24 Inch Horse Trailer Breast Pad Pre-Drilled

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching