What Thickness is the Spacer Washer for Fastway e2 Weight Distribution Head

Question

Question:

What is the thickness of this replacement spacer washer? Since the instructions are specific about washer quantity, not thickness, its important to know how thick they are so I get the right tilt. Thanks!

asked by: Brent

0

Expert Reply:

The thickness of the Spacer Washer for Fastway e2 Weight Distribution Head # FA92-04-9655 is 1/16" thick.

expert reply by: Scott S

0

Answer 1

Even though a 1" lift probably isn't going to considerably change your setup, if your trailer was level/close to level before adding a RoadActive RAS system like the #RAS3611-Y , you'll need to make some adjustments. If your trailer is…

view full answer...

Answer 2

If you want to just add on some sort of extension you can use Safety Chain Quick Link #C82932 which has a working load limit of 3300-lbs. This will give you about 3-inches additional length. Ideally trailer safety chains will be one continuous chain,…

view full answer...

Answer 3

It looks to me that you will want additional spacers to provide better weight distribution on your 2019 Ram 1500. The Fast Way e2 Weight-Distribution Hitch #FA94-00-1061 is capable of having up to 9 spacers to provide the correct pinion angle on the…

view full answer...

Answer 4

Curt hitch ball #40038 has a 1 inch diameter shank. For Curt balls with 3/4 or 1 inch diameter shanks you would use wrench #C20001. The nut on that ball should use the 1-1/2 inch end of the wrench. You could also use a large crescent wrench if you…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

Hi Ruben; thanks for the question, and while there is one rack for your 2023 Ford F-150 with a 6-1/2' bed compatible with the Pace Edwards UltraGroove Metal Retractable Hard Tonneau Cover #PE66UV, it does not have sides, and is part #TX84NV.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

I have a solution for you Travis as Pace Edwards does not offer a contractor rack for your 2023 GMC Sierra 1500. Instead you can use the Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover #311-M-FMCA28A59 with the Thule TracRac SR…

view full answer...

Answer 10

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What Thickness is the Spacer Washer for Fastway e2 Weight Distribution Head

Product Page this Question was Asked From

Continue Researching