Can a B&W Companion 5th Wheel Hitch Be Locked Out To Prevent Sliding

Question

Question:

I have a BandW companion 5th wheel hitch in my 2022 Ram 2500 CrewCab with the 6’ bed. I have a Reflections 150 Series 280RS. I has the ability to change the pivot point of the 5th wheel back to the bumper. I purchase a block to lock the trailer from tuning on the hitch in the truck. Are using blocks to lock the hitch a good idea and safe for towing and longevity? Thank you.

asked by: Jim H

0

Expert Reply:

Yes It's completely fine to lockout your B&W Companion OEM 5th Wheel Trailer Hitch w/ Slider for Ram Towing Prep Package # BWRVK3670.

However, preventing this hitch from sliding isn't a good idea with a short bed, unless you have a pivoting pin box. Otherwise, you are going to run into clearance issues between the cab of your truck and your trailer.

But, it sounds like you already have this on your trailer so you'll be just fine. Also, as long as you take care of your hitch and keep it properly maintained as specified by the manufacturer, it'll last you just as long as if you used it as a slider.

expert reply by: Bryce D

0

Answer 1

I was able to pull up the owners manual for the Lippert Turning Point pin boxes and it is pretty simple to lock out the pin box so that you could use it with an auto sliding Demco Hijacker like you have. Basically you just install two 5/8" - 11…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 9

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 10

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…

view full answer...

Answer 11

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Can a B&W Companion 5th Wheel Hitch Be Locked Out To Prevent Sliding

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching