Can the Touchscreen Remote LC358601 Be Used to Replace a Lippert Components IDS Transmitter 329164

Question

Question:

I have a 2012 Forest River Cherokee and I broke my remote screen. The remote is a 15004-f Serial number 35B7FE0C with graphics pack 1524-E. Will this remote work as a replacement and if not, what would? Thanks for the help.

asked by: Joe S

0

Expert Reply:

Thank you for the pictures, it looks like you have the Lippert Components IDS Touch Screen Transmitter 329164.

You can in fact use the Replacement Touchscreen Remote w/ Charger # LC358601 that you were looking at as a replacement option for that controller/transmitter.

expert reply by: Scott S

0

Front View of Lippert Components IDS Touch Screen Transmitter 329164
(click to enlarge)

Back View of Lippert Components IDS Touch Screen Transmitter 329164
(click to enlarge)

Answer 1

In order to sync the Replacement Touchscreen Remote part #LC358601 with the multi-function pad on your 2015 Keystone Cougar 327RES you are going to want to complete the following: 1) To begin syncing the remote to the receiver, both the receiver and…

view full answer...

Answer 2

If the remote you are talking about is the Touchscreen Remote w/ Charger for Lippert Ground Control 3.0 Electric Leveling System #LC358601. Then yes, we do have a replacement charger. - Replacement Charger for Lippert Ground Control 3.0 Touchscreen…

view full answer...

Answer 3

Thank you for the extra information! In your previous question you stated that you had pressed the left button five times and then the right button five times but nothing happened. If you check out the attached clip from the instructions of the…

view full answer...

Answer 4

I spoke with my contact at Lippert who said that if you press the silver button on the Touchscreen Remote #LC358601 10 times (prior to entering any code) then the remote will go into a calibration mode. If this doesn't fix your problem then the…

view full answer...

Answer 5

A separate owner's manual is not included with the Lippert Replacement New-Style Linc Analog Remote #LC292614, however I have attached a couple images of the instructions that I was able to track down. This will walk you through how to sync the…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Answer 9

It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Can the Touchscreen Remote LC358601 Be Used to Replace a Lippert Components IDS Transmitter 329164

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching