Threads Per Inch for Replacement Yakima HoldUp Bike Rack Hitch Bolt

Question

Question:

What is the thread pitch on this bolt? I need it to be a 5/8-11 for a number of reasons. Thank you.

asked by: Ed M

1

Helpful Expert Reply:

The bolt that comes with the Replacement Hitch Hardware for Yakima HoldUp Bike Racks # 8890260 has 5/8" diameter threads with the coarse (5/8" - 11) thread spacing so it will work for your application.

expert reply by: Jon G

1

Dimensions of Boltfor Hitch Hardware for Yakima HoldUp Bike Racks
(click to enlarge)

Answer 1

The Replacement Tongue for Yakima HoldUp Bike Racks #8880580 will keep the Replacement Hitch Hardware for Yakima HoldUp Bike Racks #8890260 in place still inside the tongue when you remove the tongue from your receiver. The Yakima hold up requires…

view full answer...

Answer 2

You are in luck, one of our co-workers happens to have a Hollywood bike rack for Class II hitches and I checked several of the hitch pins that we have available to see if they would work with bike rack. I found that the SportRack Anti-Rattle Bike…

view full answer...

Answer 3

There is an SKS lock end that works with the #8890260 with the part #Y07235 but by the time you add up the cost of both parts you are better off going with a similar universal setup like the #63232 since the price is better and would work just as…

view full answer...

Answer 4

Yes, the Curt Anti-Rattle Kit for Hollow Shank #C69HR will hold up when pulling your equipment trailer. This will only work on ball mounts for a 2" receiver with a hollow shank. I feel the Blue Ox Hitch Receiver Immobilizer II #BX88224 is the…

view full answer...

Answer 5

Yes, I checked with Yakima and the Replacement Hitch Hardware for Yakima HoldUp Bike Racks part #8890260 will work with the Yakima FourTimer 4 Bike Platform Rack part #Y02469. The Yakima and the Replacement Hitch Hardware for Yakima HoldUp Bike Racks…

view full answer...

Answer 6

For this you will need the Curt Ball Mount #C45070, Curt Anti-Rattle Kit #C69HR and the Curt RockerBall Shock Absorbing 2-5/16" Hitch Ball #C82KR. The ball mount and anti-rattle kit are the same ones that are included with the Curt RockerBall…

view full answer...

Answer 7

The Curt RockerBall Anti-Rattle Towing Kit #C43KR takes the additional height of the base of the RockerBall into account for the listed 4" rise and 5" drop. I have attached an image below showing how it is measured. Typically, you find the…

view full answer...

Answer 8

I checked with Yakima and for their Fourtimer bike rack part #Y02469 the correct hitch bolt is the part #8890260 and then for the matching lock assembly you'd need the #8820048.

view full answer...

Answer 9

Yes, we have either the Anti-Rattle Pin #C69HR or Locking Anti-Rattle Pin #63232 which you can use with the Curt Hitch Extender #C76DR.

view full answer...

Answer 10

The Yakima Replacement Hitch Hardware for Yakima HoldUp Bike Racks #8890260 that you referenced is Metric.

view full answer...

Answer 11

The Yakima Holdup 2 bike rack 2009-2012 which fits inside a 2" receiver is model number 8002433. This will use the Replacement Tilt Pull Pin #Y39FR. The Anti-Rattle #8890260 is the correct anti-rattle as is the End Cap #8880228. I do not see…

view full answer...

Answer 12

There are a few options to help reduce the sag on your 2013 Toyota Sienna when pulling a trailer. I recommend Air Lift AirLift 1000 Air Helper Springs for Coil Springs - Rear Item #AL60732. These are air bags that fit inside your factory coils.…

view full answer...

Threads Per Inch for Replacement Yakima HoldUp Bike Rack Hitch Bolt

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching