How To Retention A Solera Slide Out Awning
Question:
Slide toppers like the Solera RV Slide-Out Awning # LCV000168109 need to be rolled 12 - 16 times for proper tension. When rolling the heads to get the 12-16 times for tension do I have the awning roldup or is this tension done when extended out?
asked by: James W
Helpful Expert Reply:
To retention your Solera RV Slide-Out Awning # LCV000168109 you'll want to extend the slide out and can then get on a ladder and get up to the arms. You'll disconnect the extension rod # LC3452072 from the arm and then can roll the arm 12 - 16 times towards the trailer and slip a pin or small screwdriver through the slot in the connection point between the arms and the roller tube to lock the arm in place and then reconnect it to the extension rod.
Once both arms are reset you can roll the roller tube a bit towards the trailer to remove the pins or screwdrivers locking the arms in place and slightly grip the roll tube as it retracts and winds up the fabric on the roller tube. You'll want to run the slide out in and out a few times to get the wrinkles out of the fabric and then you can reinsert the screws holding to the fabric into the extrusion rail.
Products Referenced in This Question
Replacement Extension Rod for pre-2022 Solera RV Slide-Out Awning - Black - Qty 1
- Accessories and Parts
- RV Awnings
- Extension Rod
- Solera Replacement
- Black
- Lippert
more information >
Product Page this Question was Asked From
Solera RV Slide-Out Awning - 157" Wide - Black
- RV Awnings
- Slide-Out Awnings
- Extends 48 Inches
- 152 Inch Wide
- 153 Inch Wide
- 154 Inch Wide
- 155 Inch Wide
- 156 Inch Wide
- 157 Inch Wide
- Black
- Lippert
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Kuat NV 2.0 Bike Rack for 4 Bikes - 2" Hitches - Wheel Mount - Gunmetal Gray
- Q&A: How to Add Tension to Solera Slide-Topper
- Shop: Kuat NV 2.0 Base Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Matte Black
- Video: Kuat NV 2.0 4-Bike Platform Rack Test Course NV22G-NA22G
- Video: Kuat NV 2.0 4 Bike Rack Review
- Q&A: Can I Add Two More Bikes To The Kuat Sherpa 2.0?
- Shop: Thule Hitching Post Pro Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches
- Article: Best Bike Racks for Electric Bikes
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: 44649
- Shop: Trailer Hitch
- Video: Hollywood Racks Destination E Bike Rack Review
- Search Results: dust caps
- Q&A: Is It Better To Carry Bikes Behind Flat Towed Vehicle or Above Tow Bars?
- Shop: Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
- Shop: Trailer Wiring
- Search Results: hitch bike racks
- Q&A: What Are the Differences Between the Kuat Piston Pro and Piston Pro X Bike Racks
- Shop: Hollywood Racks Destination Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
- Article: How to Choose a Hitch-Mounted Bike Rack
- Shop: Roof Rack
- Video: Hollywood Racks Sport Rider SE 2 Electric Bike Platform Rack Review
- Shop: Brake Controller
- Video: Comparing the Kuat NV and the Thule T2 Pro Bike Racks
- Article: Best Bike Racks for Fat Bikes
- Search Results: bike rack
- Shop: Hollywood Racks Destination Bike Rack for 4 Bikes - 2" Hitches - Frame Mount
- Q&A: Differences Between Kuat Sherpa 2.0 and NV 2.0 Bike Racks
- Video: Comparison of the Hollywood Destination and the Yakima On Ramp E-Bike Racks
- Article: Trailer Wiring Diagrams