Can I Put A B&W Turnover Ball In My 2019 F-350 With The Factory Puck System?
Question:
Can I use a gooseneck under bed system on a 2019 F-350 that already has the puck system
asked by: Huck W
Expert Reply:
No, you would not be able to install an aftermarket gooseneck hitch like the # BWGNRK1108 on a truck that already has the factory puck system. Parts of the puck system would obstruct both the frame brackets and crossmembers of the gooseneck hitch. The puck system would have to be completely removed, which in my opinion is not a logical thing to do and would be way more trouble than it is worth.
If the factory puck system has a gooseneck ball spot already you can just drop in the B&W gooseneck ball # BWGNXA2061. This kit comes with the ball and safety chain loops and will be all you need to be able to tow gooseneck.
If your puck system does not have the center hole, you can use the Reese Elite # RP30845. This will have identical spacing to the ford puck system (13 inches apart from front to back and then 30 inches apart from left to right).
Products Referenced in This Question
B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Gooseneck Hitch
- Below the Bed
- Manual Ball Removal
- 7500 lbs TW
- 30000 lbs GTW
- Removable Ball - Stores in Hitch
- Wheel Well Release
- 2-5/16 Hitch Ball
- B and W
more information >
B&W Ball and Safety Chain Kit for Ford, GM, Chevy, and Nissan Titan XD Underbed Gooseneck Hitch
- Gooseneck Hitch
- Below the Bed
- Manual Ball Removal
- 30000 lbs GTW
- Removable Ball - Stores in Truck
- In Bed Release
- 2-5/16 Hitch Ball
- B and W
more information >
Reese Elite Series Above-Bed Gooseneck Trailer Hitch - 25,000 lbs
- Gooseneck Hitch
- Gooseneck for Fifth Wheel Rails
- Fixed Ball
- 6250 lbs TW
- 25000 lbs GTW
- Fixed Ball - Centered
- 2-5/16 Hitch Ball
- Reese
more information >
Product Page this Question was Asked From
B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Gooseneck Hitch
- Below the Bed
- Manual Ball Removal
- 7500 lbs TW
- 30000 lbs GTW
- Removable Ball - Stores in Hitch
- Wheel Well Release
- 2-5/16 Hitch Ball
- B and W
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Does HBA-CAM Adapter Module for Hydrastar Electric Over Hydraulic Brake Actuators have 2 or 4 Wires
- Article: What is Overlanding? How to Start your Overlanding Journey
- Q&A: Availability of 7-1/2-inch-long V-Shaped Replacement Keel Roller for Boat Trailer
- Q&A: Trailer Suspension Hanger Kit for Slipper Springs and 38 inch Wheelbase
- Q&A: Solution for Atwood Surge Brake Coupler Needing Replacement Parts
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Article: 5 Things to Know About Weight Distribution Hitches
- Q&A: Wiring Diagram for 7-Way Round Pin Trailer and Vehicle Side Connectors
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Article: How to Replace or Install an RV Roof Vent
- Article: 2023 Holiday Must Haves
- Article: How to Charge a Trailer Battery While Driving: 3 Common Problems (And How to Fix Them)
- Article: How to Accurately Measure Trailer Leaf Springs
- Article: Pintle-Hitches