Replacement Trailer License Plate Light For Incandescent Light Sealed Inside Lens

Question

Question:

I would have to break the lens to get to the bulb. It is a clear lens and looks like it is well sealed.

asked by: Charles K

0

Expert Reply:

Thank you for the images. It appears you have a Mini Trailer License Plate Light # LP91CB which is 2-1/2" long by 1-3/6" tall. You will have to replace the light as an assembly since the unit is sonically sealed to prevent water from getting in. You will be able to use the LED Trailer License Plate Light # LPL91CPG as a replacement if your light does match the dimensions above. The LED will last longer and draw less power from your vehicle.

expert reply by: Bud M

0

Trailer License Plate Light
(click to enlarge)

Trailer License Plate Light Electrical Connector
(click to enlarge)

Answer 1

Yes, the Tekonsha BRAKE-EVN part #TK63VR will be a direct replacement for the Reese Tow Power you have now. It will plug right in using the same connector.

view full answer...

Answer 2

For an exact replacement for the #LP91CB that is LED you would want the part #LPL91CB.

view full answer...

Answer 3

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 4

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 5

In order to install a brake controller on a dump truck you'd first need to start with a 4-way trailer connector and then adapt this to a 7-way so you can hook up a brake controller. I won't have much info for anyone particular dump…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 8

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Replacement Trailer License Plate Light For Incandescent Light Sealed Inside Lens

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching