What's The Difference Between The Valterra Waste Valves # T40C And # T40D

Question

Question:

what is the differents between the t40D and the T40C valterra valve

asked by: Larry B

1

Helpful Expert Reply:

The Valterra Bladex Waste Valve for RV Black Water Tank - 3" FPT to 3" MPT # T40D has male and female threaded connectors while the Valterra Bladex Waste Valve for RV Black Water Tank - 3" Hub to 3" MPT # T40C has a threaded male fitting and non-threaded hub fitting.

expert reply by: Kevin C

1

T40C Waste Valve
(click to enlarge)

T40D Waste Valve
(click to enlarge)

Answer 1

We have exactly what you are looking for as the part #T40D. This has the same 3 inch male and female threaded ends as what your picture has. I attached a review video for you to check out as well.

view full answer...

Answer 2

Thank you for the photos! Based on that it looks like you have a spigot to hub black water tank valve, like you mentioned, where the hub end fits over one pipe and the spigot end fits into the other pipe. So for a spigot to hub replacement valve with…

view full answer...

Answer 3

The difference between the Valterra RV Waste Valve #T60, and the Valterra RV Waste Valve #T60A, is that #T60 is a 3" Hub, and #T60A is a 3" Spigot. The difference between a spigot and a hub, is that a spigot is something that is to be…

view full answer...

Answer 4

I have a solution for you, but the Go Power RV Converter and Smart Battery Charger - 12V - 35 Amp #34266167 is not compatible with Lithium batteries. Instead, I recommend the Progressive Dynamics Inteli-Power RV Converter and Battery Charger -…

view full answer...

Answer 5

The Progressive Dynamics Inteli-Power RV Converter and Battery Charger - Lithium - 12V - 60 Amps #PD9160ALV is designed to work with lithium iron phosphate batteries. And the Charge wizard is not compatible with this either. However the Progressive…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

Hey Jeff, appreciate all the details you provided that was super helpful and we do have the MORryde cushioned pin box that is designed to replace a Lippert Rhino pin box. For the 17,695 lb GVWR you mentioned on the 2024 Brinkley Model Z 3610, what…

view full answer...

Answer 8

Hey Mark, since we know your Brinkley Z3100 has the Rhino style pin box, the correct Gen-Y fifth wheel to gooseneck adapter is the part #GY98GR which comes with the auto latch you mentioned wanting as well!

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

There is a solution for you, but the lift kits you referred to such as #K71-725-02 will not work with welded on torsion axles. The best option is for you to simply remove your torsion axles and use the Timbren Axle-Less Trailer Suspension System…

view full answer...

Answer 11

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 12

The Access Toolbox Edition Soft, Roll-Up Tonneau Cover #A93VR is designed to fit the youru 2022 Ram 3500 with a 8' dually bed. The Cover #A37FR will only fit an 8' bed with single rear wheels. This is the only difference in these covers is…

view full answer...

What's The Difference Between The Valterra Waste Valves # T40C And # T40D

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching