Dimensions of K Source Universal Low-Mount Style Door Mirror

Question

Question:

Hello! I have a 1997 F250 and I want to replace the factory black mirrors with the classic stainless towing mirrors. I will be pulling a horse trailer every now and then, and I think they just look sweet. I was wondering what the distance between the upper holes for this mirror and the length and width of the plate that attaches closer to the window - the top attachment sorry, not sure what to call this part Thanks! I appreciate it!

asked by: Rose

0

Expert Reply:

The distance between the lower arms on the K Source Universal Low-Mount Style Door Mirror # KS29MD runs 8-10" for installation. K Source was unable to give me the length and width of the mounting plate but the distance between the mounting holes is 3-7/8" so the overall length of that plate is approximately 8".

I have attached the instructions in a picture below which include these measurements for your reference.

expert reply by: Robin H

0

K Source KS29MD Instructions.
(click to enlarge)

Answer 1

The top mounting hole measured center to center to the bottom mounting hole is 18". The overall length of the arm is 19 1/4". The mirrors are going to be a bolt on installation, it may require drilling if existing holes are not present. All…

view full answer...

Answer 2

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Answer 8

We have one option that will work for you. The Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2 #8-407-5UC3-EZ uses inner bearing #L68149 and outer bearing #LM67048 so it would work perfectly on your spindle.…

view full answer...

Answer 9

Most critical to trailer tire performance and durability are 1) proper inflation 2) observance of the tire's rated load capacity and 3) observance of the tire's speed rating. If either of these factors is off the mark then the tire will tend…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

I wish I could say yes, but as of right now they are not a fit for the 2016 models and we do not have any other suspension enhancement options. If you are trying to fight suspension sag from the tongue weight of a trailer there is a better option. A…

view full answer...

Answer 12

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Dimensions of K Source Universal Low-Mount Style Door Mirror

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching