Trailer Fenders in Black For 145R12 Tires & Mounting Brackets

Question

Question:

I have a LoadRite aluminum single jet ski trailer with plastic fenders. The Load Star ST145R12 don’t clear the fenders now. Which fenders and mounting brackets do I need to fit the new tires?

asked by: Don G

0

Expert Reply:

For a single axle trailer fender in black that will work with 145R12 tires and wheels you need the Single Axle Trailer Fender # F008559.

You will also use the Mounting Brackets for Trailer Fender # CE26061G-2.

expert reply by: Kyle S

0

Answer 1

For a metal trailer fender the part #CE17701G would be a great option for a smaller trailer like what you have. I attached a picture of what it looks like installed on a similar trailer. I also attached a review video for the fenders. For install…

view full answer...

Answer 2

I have attached a chart for you to take a look at that includes the lug nut torque specifications. If your wheel uses 1/2 inch lug nuts or wheel bolts like the 12 Inch Steel Spoke Trailer Wheel #AM20124 referenced in your question, you will torque…

view full answer...

Answer 3

The two tire sizes you referenced, 4.80-12 and 5.30-12, both fit 4-inch wide rims, but they differ in their overall diameter. A 4.80-12 tire/wheel when fully inflated will have a diameter of 20-1/2-inches while the 5.30-12 size will be just under…

view full answer...

Answer 4

You can replace a 4.80-8 trailer tire with a 4.80-12 or a 5.30-12 trailer tire, but there are a few things to consider before making the change. First, 4.80-12 and 5.30-12 tires are going to have a larger overall diameter than a 4.80-8 tire, by about…

view full answer...

Answer 5

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 11

The B&W Companion OEM 5th Wheel Trailer Hitch #BWRVK3700 is perfectly compatible with cushioned pin boxes like your MORryde RP072-1621HD, so the clunking you're experiencing isn't related to the two components being incompatible. With…

view full answer...

Answer 12

It's totally normal for a bit of movement between any fifth wheel hitch and the base rails. The feet on the hitch are typically a bit smaller than the slots they slide into for mounting otherwise you'd have a hard time getting your hitch in…

view full answer...

Trailer Fenders in Black For 145R12 Tires & Mounting Brackets

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching