Brake Assemblies that Fit 5,200 Trailer Axles of RV Trailer

Question

Question:

Hello, I currently have new toy hauler and I’m trying to figure out the brakes. Has two 5200lbs axles, would a pair of 3500lbs brakes work pr axle? So a total of four 3500lbs brakes. Thank you

asked by: Keith

0

Expert Reply:

Since you have 5,200 lb axles you will need 5,200 lb brake assemblies which we have a set for that with the part # AKEBRK-6. Not only is this the correct rating but a lower capacity assembly like 3,500 won't fit as the diameter would be too small.

expert reply by: Jameson C

0

Answer 1

Based on the information we have in our system you will need either the Lippert #LC66WD or Dexter #K23-478-479 brake kits for each of your axles depending on who manufactured your axle. These are 10" diameter by 2-1/4" wide brake…

view full answer...

Answer 2

We very likely have the correct electric drum brakes for your 2020 Forest River No Boundaries 19.5 travel trailer, but don't know offhand which brakes you need. To find the correct brakes, you just need to know the weight capacity you need, and…

view full answer...

Answer 3

You will need to do some measuring to determine if the 10 Inch Electric Brake Assembly LH, item #AKEBRK-35L, is the correct assembly for your trailer. Measure the diameter of the mounted brake shoe, the width of the lining and the distance between…

view full answer...

Answer 4

Installing a 4,000 lb capacity leaf spring on a trailer with a 3,500 lb capacity axle will make the suspension stiffer which could then in turn minimize the risk of the axle contacting the frame. However, this is not what I recommend to fix your…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Brake Assemblies that Fit 5,200 Trailer Axles of RV Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching