Availability of Trailer Tire in Size 6.90-8

Question

Question:

I have a 6.90-6.00-9 tire 8 ply I am looking for something that size any help would be great

asked by: Thomas M

0

Expert Reply:

We currently have one tire in the size you have with the Kenda Loadstar K364 part # AM10040. This is a Load Range C that has weight capacity of 1,298 lb at 60 psi.

expert reply by: Jameson C

0

Answer 1

I can help you with determining the correct replacement wheel and tires for your trailer with a 6.90-9 tire. Normally you would just need to measure the diameter of the wheel to get the size, but we know a 6.90-9 tire fits a 9" x 4-1/2" or…

view full answer...

Answer 2

The closest standard trailer tire size to 22 inches overall is the 5.30-12 which has an overall diameter of 21.9 inches. This tire size there are only bias ply tires available like the part #AM30780 for if you have a 4 on 4 inch bolt patter or the…

view full answer...

Answer 3

The best option we can offer you would be to replace just the tires using the Kenda Loadstar K364 Trailer Tire part #AM10040 which will allow you to use your existing wheels saving you a bit of cash. These tires are tubeless so you won't have to…

view full answer...

Answer 4

The tire you referenced, Kenda Loadstar K364 Trailer Tire 6.90/6.00-9 in Load Range C, item #AM10040, has a weight capacity of 1,298-lbs at 60-psi for EACH tire. It is likely that the special purpose industrial tire you mentioned has that slightly…

view full answer...

Answer 5

First off, the 9 must represent the wheel diameter, which is an odd size. So if 9 is the diameter that would make 4-1/2 and 5-1/2 the width. The diameter is not the actual overall diameter of the wheel, it is the diameter of where the tire sits on…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Availability of Trailer Tire in Size 6.90-8

Product Page this Question was Asked From

Continue Researching