How is Better Bath RV Sink LC385313 Secured to Counter

Question

Question:

how do you fasten the sink down when mounted on top of counter?

asked by: Mike B

0

Expert Reply:

You will secure the Better Bath RV Kitchen Sink # LC385313 to your counter by putting some butyl tape under the edges, and then finish by putting 100% silicone sealant all around the edges.

expert reply by: Kyle S

0

Answer 1

You could definitely install the Better Bath Single Bowl RV Kitchen Sink part #LC385313 as an over mount. The flange would be a little flat and not tapered down like you see on most over mount sinks but as long as that's not an issue for you this…

view full answer...

Answer 2

The Better Bath Single Bowl RV Kitchen Sink - 26" Long x 16" Wide - Stainless Steel #LC385313 is designed to be an undermount sink, which is where I think the confusion might be coming. I saw both of the answers you were looking at, and one…

view full answer...

Answer 3

According to the instructions for the Better Bath Single Bowl RV Kitchen Sink #LC209351, you will slip the "L" brackets over the studs, and lightly tighten the wing-nut. You'll want to make sure that the "L" bracket is on the…

view full answer...

Answer 4

The usual configuration for 4-pole trailer wiring has the WHITE wire as GROUND, the BROWN wire as RUNNING LIGHTS, the YELLOW wire as LEFT TURN/STOP and the GREEN wire as RIGHT TURN/STOP. If your light has white and brown wires coming out of it then…

view full answer...

Answer 5

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 6

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

How is Better Bath RV Sink LC385313 Secured to Counter

Product Page this Question was Asked From

Continue Researching