Roof Rack For Camper Shell on 2014 Toyota Tacoma

Question

Question:

I have a 2014 Tacoma Short bed with a Snugtop Camper Shell. What do you recommend for Rack/Bars and Tracks for carrying 2 Kayaks? I want to put them on top of camper shell, and they be removable.

asked by: JEFF&TONJA

0

Expert Reply:

Sure thing, you can put a roof rack on the camper shell of your 2014 Toyota Tacoma, you'll just need to add the Rhino-Rack Aero Bar Roof Rack for Camper Shells - Track Mount - Black - 59" Bars # Y02-490B.

expert reply by: Kyle S

0

Answer 1

I have a solution for you, but there are not brackets to mount the Rhino Rack Pioneer platforms directly to your truck topper. I recommend adding a track system to the roof of your topper. You will use the Rhino-Rack RTC-Style Roof Rack Tracks #RTC14…

view full answer...

Answer 2

Yes, the 63" Rhino-Rack RTC-Style Roof Rack Tracks - Channel Mount part #RTC16 can be cut down to the size you need as long as you cut them perfectly straight to allow the end caps to go back on because at this time we do not carry them as a…

view full answer...

Answer 3

There a few options to add a rack to the Leer Canopy on the 2020 Chevy Silverado depending on if you have the tracks in your canopy already. I recommend Rhino Rack part #Y01-140B which comes with the tracks to install into your canopy. This will…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

Tracks can absolutely be installed on the roof of your A.R.E. Truck Cap to provide a mounting system for a roof rack. For this I recommend the Yakima Tracks, which come in 42 inch #Y01126, 54 inch #Y01127, and 60 inch #Y01135 lengths. These tracks…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Roof Rack For Camper Shell on 2014 Toyota Tacoma

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching