Vertical Dimensions for the Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning

Question

Question:

Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning Item # 8880736. Rail spacing. What is the vertical spacing , between the center of the top bolt and the rail on the bottom ? Basically I am looking for the rail spacing. Thanks for the help

asked by: Hans K

0

Expert Reply:

The vertical spacing you're asking for is 1-1/2" for the Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning # 8880736 (see attached).

I confirmed this with my contact at Yakima.

expert reply by: Jon G

0

Vertical Dimensions of Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning
(click to enlarge)

Answer 1

Yes, you can use the Replacement Clamp Assembly #8880737 and Replacement Mounting Bracket #8880736 for the Yakima SlimShady will work for your Roam awning. We actually have a review from a customer who purchased this combination for the same exact…

view full answer...

Answer 2

The bolt hole spacing for the Replacement Mounting Bracket #8880736 is 4" on center (see attached). This will fit with the Replacement Clamp Assembly #8880737 and to your 2008 Honda Element factory crossbars just fine, you just have to make sure…

view full answer...

Answer 3

I attached a picture that I got from Yakima that shows how the install bracket for the SlimShady part #8880736 installs.

view full answer...

Answer 4

I have a solution for you, but those parts are not available from Yakima at this time. Instead, you'll need to replace the entire assembly on your Yakima Slim Shady Awning #Y36VR. You can use the Replacement Clamp Assembly for Yakima SlimShady…

view full answer...

Answer 5

The fit of the #8880736 is very tight to the lower base it attaches to and is mostly covered when the awning is installed. Since both of the brackets would have to come off at the same time it would take a thief who knew the awning setup very well…

view full answer...

Answer 6

I was able to confirm with my tech contact at Yakima that all of the bolts in the Replacement Hardware for a Single Yakima Universal MightyMount 2005 and Newer #8880056 have 5/16" x 18 thread pitch. This would be the same for all of the hardware…

view full answer...

Answer 7

The Yakima Replacement Clamp #8880737 referenced in your question comes with 1 clamp assembly. For a pair you will just need to order 2 of the clamps. These are designed to fit the Yakima SlimShady Roll-Out Awning #Y36VR.

view full answer...

Answer 8

The Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning part #8880736 is designed specifically for the Yakima SlimShady roll-out awning part #Y36VR. If you have the manufacturer and model information off of your awning I can help to…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Dominick, Yes, we offer the 58" long Malone AirFlow2 Roof Rack in black with Item #MAL84AR. If you need anything else just let me know and I'd be happy to help.

view full answer...

Answer 11

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Vertical Dimensions for the Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning

Product Page this Question was Asked From

Continue Researching