Recommended Ladder Rack and Tonneau Cover for a 2016 Toyota Tundra w/ 5-1/2 Foot Bed and Rail System

Question

Question:

Hello, Can your team please recommend a high weight capacity rack at least 1000lbs and tonneau cover combo for a 2016 Tundra CrewMax 5-1/2’ bed? I like the TracRack with cab extension, would that be compatible? Thanks!

asked by: Matt W

0

Expert Reply:

Since your 2016 Toyota Tundra has the 5-1/2' bed and the deck rail system you are going to want the Thule TracRac SR Sliding Truck Bed Ladder Rack item # TH97RV. For the cab extension you will need the Cantilever Extension item # TH24001XT. There is no all in one kit available for the 5-1/2' bed trucks so you will need to purchase the two pieces separately.

Thule TracRac SR Sliding Truck Bed Ladder Rack item # TH97RV has a 1,250 lbs capacity but the Cantilever Extension item # TH24001XT tops out at 1,000 lbs so if you're hauling something large enough to reach the extension you will want to stick to the 1,000 lbs limit.

For a compatible tonneau cover, I recommend the BAK Revolver X4s Hard Tonneau Cover item # BAK28ZR. You are going to need a cover that leaves the side rails open so you can mount the Thule SR ladder rack. That ladder rack mounts directly to the stake pockets. Additionally, the weight capacity you need requires you to use a tonneau cover like the Revolver X4. The hard top folding covers attach the ladder racks directly to the cover using T-slots which reduces the capacity to 300 lbs. If you find one that mounts inside the rails you won't be able to open the folding cover because of the angle of the ladder rack uprights.

The BAK Revolver X4s Hard Tonneau Cover item # BAK28ZR bolts to the inside of your bed with included hardware and clamps. It has a pull cable that lets you open the cover from either side of your Tundra's bed.

expert reply by: Jerred H

0

Answer 1

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 2

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 3

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 4

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 5

Hey Chad, so I'd actually recommend a mid size ladder rack like the Yakima OutPost HD Overland Truck Bed Rack #Y01152-58. This is by far going to be your best bet if you don't want to trailer your kayaks. These bars have a 500 lb weight…

view full answer...

Answer 6

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 7

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 8

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Answer 9

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 10

From your question it sounds to me like someone has cut off the tow package plug on your 2005 Ford F-150 and wired in a 4-way connector. In this case you could use the Hopkins Adapter 4-Pole to 7-Pole and 4-Pole, #37185 which will give you a 4-way…

view full answer...

Answer 11

I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The easiest…

view full answer...

Answer 12

Yes, to both of your questions! The Mountain Top EVO-M Retractable Hard Tonneau Cover with T-Slot Accessory Rails - Aluminum item #MNT29FR is confirmed to fit the 2021 Chevy Silverado 1500's with a 6-1/2' bed. It is also compatible with the…

view full answer...

Recommended Ladder Rack and Tonneau Cover for a 2016 Toyota Tundra w/ 5-1/2 Foot Bed and Rail System

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching