What Are the Dimensions of the Spring-Eye Bolt with Locknut for Slipper Springs

Question

Question:

What is the length from the back of the head to the start of the threads, and the length of the threaded portion. I am looking for a solid bolt of the correct dimensions to replace a 3 3/8 Morryde wet bolt that comes in the X-Factor kits I got from you. It is being used with a Dexter EZ-Flex 13-144 center section fandom axles. This is for the top bolt that goes through the steel center bushing in the hanger. The 9/16 wet bolt provided in the kit has a slightly looser fit than the 9/16inch original bolt. I need the longer length to fit through the X-Factor backing plate like the wet bolt in the kit.

asked by: Keith

0

Expert Reply:

The Spring-Eye Bolt with Locknut for Slipper Springs # 166079 is a total of 3-1/2" long. The measurement from the back of the head to the start of the threads is 2-3/4" and the length of the threads are 3/4".

expert reply by: Scott S

0

Spring Eye Bolt with Locknut for Slipper Springs Diagram
(click to enlarge)

Answer 1

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 2

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 3

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 6

Hey Patrick, so for your leaf spring upgrade I am going to need to know a couple of things before I can get you over to the right part. Specifically, the length from eye to eye, the spring width, leaf thickness, and the number of leaves. From here I…

view full answer...

Answer 7

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 8

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Answer 11

The hangers you currently have on your trailer are ones I have run into before. That being said, I spoke with MORryde and the #MR27ZR will still fit your trailer, but there is a modification that will need to be made. You’ll have to trim according to…

view full answer...

Answer 12

When replacing shackle straps they should be the same length as the ones that were previously on your tandem axle trailer; replacing them with longer straps will result in additional play in your trailer suspension which could lead to additional wear…

view full answer...

What Are the Dimensions of the Spring-Eye Bolt with Locknut for Slipper Springs

Product Page this Question was Asked From

Continue Researching