Replacement Lift Assist Strut for Lippert SolidStep RV Steps

Question

Question:

Will this strut work for the Wide Quad-Step stairs?

asked by: Clay

0

Expert Reply:

The Replacement Lift Assist Strut for Lippert SolidStep RV Steps # LC47UD is for the Lippert SolidStep RV Steps for 29" to 36" Wide Doorways # LC791573, which has 3 steps.

If you can give me the exact model of your steps I'd be happy to see if we have a replacement strut for you!

expert reply by: Jon G

0

Steve

4/13/2024

I have the same LCI solid step but with 4 steps. I am looking for a strut for the assist lift system. Thank you, Steve Fenn

Reply

Jon G.

4/15/2024

@Steve According to my research it looks like the same struts are used whether you have the 3 steps or 4 steps. So if you have 26" to 29-15/16" Wide RV Door Frames you need the strut # LC67UD but if you have 30" to 33" Wide RV Door Frames you need the strut # LC47UD instead.

Reply

Steve F.

4/15/2024

Jon, there are no # on the steps. It I a Lippert solid step/4 step (wide step. Lippert sells a solid step lift assist kit wide. It has two shocks in the kit it says one for 3 step and one for 4 steps. I need the strut for the 4 steps and I can’t find one on line! Thanks , Steve

Reply

Jon G.

4/17/2024

@SteveF When I reached out to my contact at Lippert they got back with me and confirmed the replacement struts I recommended above are what you're needing. You'll need to measure the width of your doorway to determine which strut is the correct replacement.

Reply

Answer 1

For 12v Vanity lighting we only offer the following products which are all satin nickel: Item #277-000324, Item #277-000446, Item #277-000322, and Item #277-000429. I've attached a link to the RV lighting page as well.

view full answer...

Answer 2

According to Progressive Dynamics, their #PD4645V Replacement 45A converter would be the proper replacement for your Parallax 7345 power converter. The unit is designed as a direct replacement for the converter in your existing power…

view full answer...

Answer 3

The SnapPad Jack Stand Pads like part #SP54FR4 may still work with the Steady Fast or JT Strong Arm Stabilizers but you'd likely need to trim the pad where the arm attaches or raise the arm up a bit from the pads. There is a lip on the pads…

view full answer...

Answer 4

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 10

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 11

Generally speaking, the lube plate will need to cover the skid plate on the 5th wheel hitch. There are some pin boxes out there that will recommend a specific lube plate but most of the times this classification will be from the 5th wheel hitch…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Replacement Lift Assist Strut for Lippert SolidStep RV Steps

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching