Parts Needed to Install Curt Triflex in 2015 Audi Q5

Question

Question:

I have a 2015 Audi Q5 3.0 TDI with a factory installed tow package. Is this C50140 the part I need and is it the same as Audi part ZAW055204A Thanks in advance.

asked by: Neil S

0

Expert Reply:

Yes, the Curt Triflex part # C51140 is the same as the Audi Curt Triflex ZAW055204A that you mentioned. To then wire it to your vehicle the correct harness would be the part # C51120.

expert reply by: Jameson C

0

Answer 1

Yes, you can use the Reese Friction Sway control part #83660 without a weight distribution system. You would just need to use the tab part #RP26003 on the ball mount as well.

view full answer...

Answer 2

I do have ways to help with trailer sway and vehicle sag on your 2013 Volkswagen Tiguan but none of the trailer hitch receivers they have for your vehicle are compatible with a weight distribution system. Load leveling is what Volkswagen calls what…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 9

In order to install a brake controller on a dump truck you'd first need to start with a 4-way trailer connector and then adapt this to a 7-way so you can hook up a brake controller. I won't have much info for anyone particular dump truck but…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Parts Needed to Install Curt Triflex in 2015 Audi Q5

Continue Researching