Can Mulitple Gustafson 12V LED Puck Light Be Wired Together to be Controlled by a Wall Switch?

Question

Question:

I have a single puck light centered over the trailer bed. Can I pull that, run two sets of wire to two of these, and keep the puck light such that all 3 can be controlled by their switches? Any combination of on/off among them. We would use the puck sometimes, then switch to on or both reading lamps as we get tired. I have a single hole above the bed now. Want to make sure the wiring will work before cutting two new holes…

asked by: John S

0

Expert Reply:

Yes you can absolutely run 3 of your 12V puck lights like # 277-000343 together in series to be controlled by a wall switch. You'd just need to run the power wire to the power wire of one light, and then connect the ground of the first light to the power of the next until all of the lights are wired in and then run the last wire back to the ground of the switch.

Attached is a review video of # 277-000343 for you to check out as well.

expert reply by: Bryce D

0

Answer 1

The Gustafson RV LED Reading Lamp, part #277-000494 is powered by 12V DC. If you click the provided link, you can see a product description video featuring this lamp.

view full answer...

Answer 2

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 3

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 4

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 5

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 6

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

A 16 inch tire will not fit on a 16.5 inch wheel. You would either need to get new 16 inch wheels with the proper bolt pattern to match what the hubs require or to get your existing wheels you would need to go with 16.5 inch tires. You mentioned you…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

The temperature light on your Everchill RV Refrigerator w/ Freezer #324-000119 is likely flashing because of a lack of full power to the fridge. The fridge requires 11 amps. It is likely trying to use more power than what is available which is why…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Can Mulitple Gustafson 12V LED Puck Light Be Wired Together to be Controlled by a Wall Switch?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching