Recommended Replacement Black Rubber Trim Options

Question

Question:

DOES SR86ZR SCREW COVER MOLDING ONLY COME IN BLACK?

asked by: JAMES H

0

Expert Reply:

Yes, the Rubber Trim for RVs, Boats, and Utility Vehicle Trim Molding # SR86ZR only comes in black, however this is 15' and it is offered in a longer 30' length should you be interested:

-Rubber Trim for RVs, Boats, and Utility Vehicle Trim Molding # SR45ZR.

These trims measure 1/8" wide, 5/8" tall, and 15'/30' long.

expert reply by: Bryce D

0

Answer 1

Yes, the JR Products Premium Narrow RV Vinyl Insert Trim Molding #37211235 can be used in the channel on your RV that hides the screws. This trim molding is black in color, is 25 feet in length and about 3/4 of an inch wide. I have added a link to a…

view full answer...

Answer 2

I was not able to find anything relating to that part number. I was able to find the Rubber Trim for RVs, Boats, and Utility Vehicle Trim Molding #SR86ZR which is 180" so you'd have to trim this down a bit, but this could potentially work…

view full answer...

Answer 3

To get both of the 2021 Subaru Outbacks pulling the Safari Condo F1743, you would need to purchase two of the #ETBC7 kits. They would piggy back off of the existing 4 pin connections already on the vehicles, so you are already partially there. I did…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Recommended Replacement Black Rubber Trim Options

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching