BAK Revolver X4s Compatibility With A 2020 Ford F-150 Lariat

Question

Question:

I just bought a 2020 Ford f150 lariate supercrew. 145 wheelbase. Can you confirm that this BAK revolver X4s fits the truck. If not, please advise if there is an alternate part number that I should use. Thanks,

asked by: Eric

0

Expert Reply:

The BAK Revolver X4s Hard Tonneau Cover # BAK39ZR is a compatible fit for a 2020 Ford F-150 with a 5.5' bed so you'll be good to go with this tonneau cover.

I've attached a short video below where Evangeline will show you the cover in use and go over the features.

expert reply by: Kevin C

0

Answer 1

I would be happy to help. Since you replaced the Trailer Tow Parks Lamps Fuse 53 in your 2019 Ford F-150 and are now not getting any power to your 7-way connector, I recommend checking fuse 43 as it is for the trailer tow park lamps module. If that…

view full answer...

Answer 2

You will need the Replacement Rubber Block for Base Rail Installation of TracRac Sliding Ladder Racks - Qty 1 #TARB-11032-1. You can get the pocket nut separately #TA01-2100N, but the bolts and other hardware are only available in the Replacement…

view full answer...

Answer 3

The best ladder rack and tonneau cover combination for a 2019 Ford F-250 is the Thule TracRac SR Sliding Truck Bed Ladder Rack part #TH43003XT-785 and BAK Revolver X4s Hard Tonneau Cover part #BAK99ZR. The reason this is the best option is because…

view full answer...

Answer 4

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 7

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 12

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

BAK Revolver X4s Compatibility With A 2020 Ford F-150 Lariat

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching