Recommended 5,200 lbs Dexter Axle w/ a Bend

Question

Question:

Looking for 94inch #5200 Dexter axle with the bend in axle to creates zero camber

asked by: Michael G

0

Expert Reply:

The Dexter 5,200 lbs axle we have item # 6340624 is 95" long so I recommend checking your measurements again. If it is in fact 94" you will need the Dexter Trailer Axle Beam item # 8327864. This is a 7,000 lbs axle but is 94" long. Both of these axles have the bend in the middle.

expert reply by: Jerred H

0

Answer 1

According to my research, your Sure-Trac ST8216TAT-B-070 trailer has 7,000-lbs axles like the Dexter Trailer Axle Beam with E-Z Lube Spindles #8327864. However to pick the correct axle for your trailer, you are going to need to measure from spring…

view full answer...

Answer 2

I do have an option for you but you'd need to do some measuring to confirm compatibility. The two options we offer are the Dexter 7K Trailer Axle part #8327864 which measures 94" long (hub face to hub face) and the Dexter 7K Trailer Axle…

view full answer...

Answer 3

I believe you are asking for a trailer axle that is 94 inches long from hub-face to hub-face, and 79 inches long from spring-center to spring-center, and a compatible hub with a 5 on 5" bolt pattern. While there are axles that size, there are no…

view full answer...

Answer 4

You certainly can install a replacement 5.2K axle like #6340624 by using new spring seats atop the axle. I'd recommend using part #TRSS300 but it's recommended that they at least be tacked into place so they stay put.

view full answer...

Answer 5

The closest option we have that would work well is the Dexter axle part #8327864-EB which has the same spring center dimension you have of 74 inches but is 1 inch longer overall at 94 inches from hub face to hub face. This is a 7,000 lb capacity axle…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Recommended 5,200 lbs Dexter Axle w/ a Bend

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching