Replacement Hardware Kit For Mounting Class III Trailer Hitch Receiver On a 2011 Ford Crown Victoria
Question:
Hello, I recently purchased a Class 3 Trailer Hitch Curt or Reese, I cant remember which from a friend for my 2011 Ford Crown Victoria Police modeld. It did not come with hardware or any installation kit. Ive installed one before on a previous vehicle, so I know approximately what I need, but is there a kit you can recommend specifically for this application? I dont think Ill be able to get a wrench into the frame tube in order to tighten a standard hex-head bolt. Thank you!
asked by: Nick A
Expert Reply:
We do carry Replacement Hardware Kits # RHK for trailer hitch receivers. It is best to identify which receiver you have for your 2011 Ford Crown Victoria as you will need to provide the hitch model number when ordering the hardware kit. We do still carry both the Curt # 13707 and Draw-Tite # 41116 (same as Reese) receivers you can use to compare to the receiver you have to determine the correct part.
We do have the Hopkins Active Tail Light Converter with Install Kit # 46255 which you can install with the receiver. This will give you a 4-way flat connector for small trailers you may tow or Auxiliary Lights # C53201.
Products Referenced in This Question
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Draw-Tite Max-E-Loader Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Hopkins Active Tail Light Converter with Install Kit
- Trailer Wiring
- Trailer Connectors
- Vehicle End Connector
- Plug and Lead
- 4 Flat
- Hopkins
more information >
Curt Auxiliary LED Indicator Lights
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Lights
- CURT
more information >
Product Page this Question was Asked From
Replacement Hardware Kit for Trailer Hitches
- Accessories and Parts
- Trailer Hitch
- Hardware
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Replacement Hardware Kit for Trailer Hitches
- Shop: Trailer Hitch
- Q&A: Replacement Brake Assemblies and Hub/Drums for 15k Dexter Axle
- Q&A: Taillight Converter Needed To Separate Brake Lamp and Turn Signal Circuits
- Q&A: 40' Wishbone Trailer Wiring With A Ground Wire Running Down Both Sides
- Q&A: Option to Replace Jensen JRV9000R
- Q&A: Recommended Replacement For A JVR9000R RV Stereo System With Three Cameras
- Q&A: How To Convert A Wishbone Trailer Wiring Harness To A Regular 4-Flat Trailer Wiring Harness
- Article: Trailer Tire Sizing
- Q&A: No Turn or Brake Signals on Trailer on a Jeep Liberty with Tow Ready Harness 118524
- Article: Replacement Automotive Lighting
- Article: Flat Towing Package for 2007-2018 JK Jeep Wrangler and Wrangler Unlimited
- Article: How to Choose the Right Trailer Hitch Class
- Article: The Differences Between Cam Buckles and Ratchet Straps (And Who Would Win In a Fight)
- Article: My Trailer Hitch Doesn't Fit
- Article: 2023 Holiday Must Haves