How Much Side Clearance Needed to Fold Down MORryde StepAbove RV Steps

Question

Question:

For MORryde StepAbove RV Steps with Strut Assist, 4-step, how much clearance between the RV and the wall is required to fold down the steps when the RV is in a RV garage?

asked by: Larry V

0

Expert Reply:

The overall height of the MORryde StepAbove part # MR85RR above where it mounts to the door frame is 47-3/4 inches which would be the same amount of distance you'd need between the side of your RV and anything to the side of it to allow the steps to swing down.

expert reply by: Jameson C

0

Answer 1

The difference is between just the MORryde Locking RV Storage Box #MR43RR and when you add the brackets at their widest setting. Just the box measures 25-3/4" but when you add the mounting brackets is when you'll see that 27-3/4" width…

view full answer...

Answer 2

Based on what MORryde told you you'd need of the STP-214 you'd need our part number #MR85RR. The STP-212 is the version of this step that does not have the strut assist so you'd want the #MR85RR.

view full answer...

Answer 3

Yes, the MORryde StepAbove RV Steps #MR28RR will work the same way as the version #MR85RR that has the strut assist. The only difference is that you either have a totally manual lift or you get the strut assist to make moving the steps up and down…

view full answer...

Answer 4

The depth of the MORryde StepAbove Strut Assist Fold-Down Step #MR85RR is 12-5/16 inches when it is in the up and folded in position. Basically it's how far the steps would take up inside the RV.

view full answer...

Answer 5

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 6

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

You can get a new brake mounting flange for your axle. The old flange will need to be cut off. The part is #4-44-1. This is designed to fit a 3 inch trailer axle and should be welded in place by a professional. Since you would also have to get the…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

We do have 205/75R14 size radial tires that have a load range of D and a speed rating of at least 81 mph. Out of our available selection I recommend going with the Kenda Karrier #AM10235. This tire has a max load rating of 2,200 lbs at 75 psi and a…

view full answer...

Answer 11

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Answer 12

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

How Much Side Clearance Needed to Fold Down MORryde StepAbove RV Steps

Product Page this Question was Asked From

Continue Researching